Ambit U10C034 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 90

background image

U10C034 Telephony Version v1.4 June 2008

74

5.4 Battery Trap

The following traps will be sent to SNMP management if battery status is changed. MSO operators
can understand current battery and modem situation when trap is received..

PS: NMAccess must be configured for SNMP trap sent.

Alarm Name

OID

Description

upsAlarmGeneralFault

1.3.6.1.2.1.33.1.6.3.18.0

A general fault in the UPS has been
detected.

upsAlarmOnBattery

1.3.6.1.2.1.33.1.6.3.2.0

The UPS is drawing power from the
batteries.

upsAlarmLowBattery

1.3.6.1.2.1.33.1.6.3.3.0

The remaining battery run-time is less than
or equal to upsConfigLowBattTime.

upsAlarmDepletedBattery

1.3.6.1.2.1.33.1.6.3.4.0

The UPS will be unable to sustain the
present load when and if the utility power
is lost.

upsAlarmBatteryBad

1.3.6.1.2.1.33.1.6.3.1.0

One or more batteries have been
determined to require replacement.

upsAlarmShutdownImminent

1.3.6.1.2.1.33.1.6.3.23.0

The UPS will turn off power to the load in
less than 5 seconds; this may be either a
timed shutdown or a low battery
shutdown.

upsAlarmShutdownPending

1.3.6.1.2.1.33.1.6.3.22.0

A upsShutdownAfterDelay countdown is
underway.

upsAlarmUpsOutputOff

1.3.6.1.2.1.33.1.6.3.14.0

The output of the UPS is in the off state.

upsAlarmOutputOffAsRequested

1.3.6.1.2.1.33.1.6.3.11.0

The UPS has shutdown as requested, i.e.,
the output is off.

upsAlarmAwaitingPower

1.3.6.1.2.1.33.1.6.3.21.0

The UPS output is off and the UPS is
awaiting the return of input power.

bcmAlarmTempBadChargeSuspended 1.3.6.1.4.1.4413.2.2.2.1.10.4.2.0

The temperature of the device has exceeded
operational limits for safe battery charging,
and battery charging has been suspended.

bcmAlarmTempBadPowerReduced

1.3.6.1.4.1.4413.2.2.2.1.10.4.3.0

The temperature of the device has exceeded
operational limits, and the device has been
placed in low power mode in an to attempt
to reduce heat production.

«
...
72
73
74
75
76
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

DU-562M - 56 Kbps Fax

Бренд: D-Link Страницы: 31

Бренд: TP-Link Страницы: 4

Interactive DDM3500

Бренд: Ubee Страницы: 21

Total Access 1240

Бренд: ADTRAN Страницы: 146

Бренд: H3 System Страницы: 16

Бренд: Cisco Страницы: 30

Бренд: Motorola Страницы: 14

Бренд: Motorola Страницы: 58

Бренд: Motorola Страницы: 66

Бренд: Motorola Страницы: 123

Бренд: Motorola Страницы: 12

Бренд: Motorola Страницы: 16

Бренд: Motorola Страницы: 8

Бренд: Motorola Страницы: 12

Бренд: Motorola Страницы: 2

Бренд: Motorola Страницы: 188

Бренд: Motorola Страницы: 117

Бренд: Motorola Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды