Ambit U10C034 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 90

background image

U10C034 Telephony Version v1.4 June 2008

38

emtaSignalingEndptCtrlToneDetectionControl

AlarmPOSDisabled(4)

read-write

emtaSignalingPowerRingFrequency

f20Hz(1),

read

emtaSignalingRingWaveform

Sinusoidal(1)

read-write

emtaRingWithDCOffset

(1.3.6.1.4.1.4413.2.2.2.1.6.1.3.0 Integer32)

This object specifies whether the ring with DC offset option is enabled.

emtaSignalingEndptCtrlAnalogLoopback

(1.3.6.1.4.1.4413.2.2.2.1.6.4.1.1.1.x Integer32)

This object controls the implementation of the analog loopback by the
MTA. When the object is set to true(1), the MTA MUST implement analog
loopback operations. When the object is set to false(2), the MTA MUST
stop loopback operations immediately. The default value of this object
corresponds to the functionality compliant with the PacketCable
requirements.

emtaSignalingEndptCtrlLineReset

(1.3.6.1.4.1.4413.2.2.2.1.6.4.1.1.2.x Integer32)

This object controls the resetting the telephone line. Setting this object
to true(1) causes the eMTA to reset the telephone line of the corresponding
endpoint. Setting this object to false(2) does not have any affect. Reading
this object always returns 'false(2)'.

emtaSignalingEndptCtrlBoostedLoopCurrent

(1.3.6.1.4.1.4413.2.2.2.1.6.4.1.1.8.x Integer32)

This object indicates whether the loop current should be boosted (true(1))
or not (false(2)). The particular value for the loop current depends on
the particular hardware (SLIC) being used.

emtaSignalingEndptCtrlTxGain

(1.3.6.1.4.1.4413.2.2.2.1.6.4.1.1.9.x Integer32)

This Object represents the per line transmitter (A/D) gain. A positive
number reflects a signal gain; a negative number reflects a signal loss.
This Object does not reflect the desired level at the Telco (POTS) a-b
(T/R) terminals as it does not include the affects of the gain settings
on the analog interfaces which are pre-configured for a given country
specification.

The

gain

setting

specified

in

this

MIB

object

will

be

applied

on top of the preconfigured settings and therefore represents a relative
level, while ambitTxGain will overwrite the preconfigured settings and
represents a absolute level.

emtaSignalingEndptCtrlRxGain

(1.3.6.1.4.1.4413.2.2.2.1.6.4.1.1.10.x Integer32)

«
...
36
37
38
39
40
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Бренд: Patton electronics Страницы: 9

Бренд: Novatel Страницы: 148

Бренд: ZyXEL Communications Страницы: 385

Бренд: BROSTREND Страницы: 13

MagicSurfer 56K

Бренд: I/O Magic Страницы: 39

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 2

Бренд: TEKSAN Страницы: 4

Бренд: NETGEAR Страницы: 2

5G WI-FI PRO MU500

Бренд: Telstra Страницы: 26

Бренд: Cooper Bussmann Страницы: 109

Бренд: ICPDAS Страницы: 55

Бренд: NETGEAR Страницы: 24

Бренд: Microwave Radio Communications Страницы: 274

Бренд: Fujisoft Страницы: 16

DG834v2 - ADSL Modem Router

Бренд: NETGEAR Страницы: 2

Barricade SMC7904BRA2

Бренд: SMC Networks Страницы: 2

MobiiBroadband 3G

Бренд: iiNet Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды