Ambit U10C034 Скачать руководство пользователя страница 14

Страница: 14 / 90

U10C034 Telephony Version v1.4 June 2008

ORE

UNCTIONALITY

U10C034 firmware provides the following core functionality:

•

Multiple provisioning methods.

•

Support for up to 16 Upstream Service Flows (SIDs).

•

Support for various packetization rates.

•

Support of SNMP v1/v2c and v3 coexistence.

•

CPE Ethernet — 10/100 BaseT / full-duplex / auto-negotiate function-
ality.

•

CPE USB — 1.1 fully supported

•

USB to Ethernet bridging functionality

IRMWARE

UNCTIONALITY

The firmware provides the following functionality:

•

Standards compatibility as follows:

–

DOCSIS 2.0 and DOCSIS 1.1

–

PacketCable 1.5

•

Interoperability with main CMTS products.

•

MGCP signaling protocol support

•

PacketCable provisioning with SNMPv2 Network Management
capabilities.

•

Support USB and Ethernet interfaces to CPE.

•

Support Telnet access to a troubleshooting command line interface.

•

Support for automatically timing out Telnet sessions after a certain
amount of idle time.

•

Supports the AckCel technology, increasing performance of TCP
application such as FTP.

Содержание U10C034



























































































Результаты поиска

Содержание U10C034

Отзывы:

Похожие инструкции для U10C034

Бренды по названию

Популярные бренды

Ambit U10C034, Руководство пользователя

Результаты поиска

Содержание U10C034

Отзывы:

Похожие инструкции для U10C034

Бренды по названию

Популярные бренды