Ambit U10C034 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 90

background image

U10C034 MSO User’s Manual v1.4 June 2008

35

The default value of this object may change based on build specific options.
However, it's highly recommended that the default value in the image
submitted for (E)PC 1.x Certification be chosen in such a way that it
will correspond to the functionality compliant with the PacketCable
requirements and will preserve the backward compatibility with the
previously certified behavior. Note that to satisfy the latter,
'maintenanceOnCMSLoss(3)' bit should be set by default.

‧

maintenanceOnCmReset(0),

‧

maintenanceOnRFLoss(1),

‧

maintenanceOnMtaReset(2),

‧

maintenanceOnCMSLoss(3)

MaintenanceQuarantineTimeout/emtaMaintenanceQuarantineTimeout

(1.3.6.1.4.1.4413.2.2.2.1.6.2.4.0 Unsigned32)

This object identifies the length of time, in seconds, that the MTA should
maintain the line voltage after any of the endpoints enters the quarantine
state. If any of the endpoints remains in the quarantine state for longer
than

this

period

the

line

voltage

is

dropped

unless

the

maintenanceOnCMSLoss

bit is set in the emtaMaintenanceControlMask MIB. Note that the value
of this object will persist across a system reboot.

MaintenanceDisconnectedTimeout/emtaMaintenanceDisconnectedTimeout

(1.3.6.1.4.1.4413.2.2.2.1.6.2.5.0 Unsigned32)

This object identifies the length of time, in seconds, that the MTA should
maintain the line voltage after any of the endpoints is disconnected.
If any of the endpoints remains disconnected for longer than this period
the line voltage is dropped unless the maintenanceOnCMSLoss bit is set
in the emtaMaintenanceControlMask MIB. Note that the value of this object
will persist across a system reboot.

MaintenanceRFDisconnectTimeout/emtaMaintenanceRFDisconnectTimeout

(1.3.6.1.4.1.4413.2.2.2.1.6.2.6.0 Unsigned32)

This object identifies the length of time, in seconds, that the MTA should
maintain the line voltage after the RF lock with the CMTS is lost. If
the MTA remains disconnected from the CMTS for longer than this period
the line voltage is dropped unless the maintenanceOnRFLoss bit is set
in the emtaMaintenanceControlMask MIB. Note that the value of this object
will persist across a system reboot.

Differences between the private MIB feature and the PacketCable MIB feature:

• Private MIBs allow one or more of the conditions of CM reset, RF

loss, MTA reset, and CMS loss to be configured. The configurability
for CMS Loss is not available for PacketCable MIBs.

• The pktcEnNcsEndPntLVMgmtResetTimer applies to all the conditions

of CM reset, RF loss, MTA reset, and CMS loss. The timers (the timeout
MIBs) from private MIBs can apply to individual condition for CMS
loss and RF loss, but there is no timer specific to CM reset and
MTA reset.

• In the event of a RF Loss, the PacketCable MIB feature will complete

«
...
33
34
35
36
37
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Бренд: Patton electronics Страницы: 10

Бренд: Real Time Devices Страницы: 33

Бренд: NBN Страницы: 8

CellPipe IAD 4A

Бренд: Lucent Technologies Страницы: 28

Бренд: Genexis Страницы: 34

E831-RTU Series

Бренд: Ebyte Страницы: 21

Бренд: CTC Union Страницы: 20

Бренд: CTC Union Страницы: 46

Бренд: Paradise Datacom Страницы: 354

Бренд: M2M Страницы: 10

Бренд: US Robotics Страницы: 152

Бренд: US Robotics Страницы: 80

Бренд: IPWireless Страницы: 24

Бренд: RACOM Страницы: 27

Бренд: D-Link Страницы: 8

Бренд: Fargo Страницы: 23

Бренд: Pantech Страницы: 2

Бренд: NetComm Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды