Ambit U10C034 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 90

background image

U10C034 Telephony Version v1.4 June 2008

48

emtaSignalingDevToneFreqOnDuration and
emtaSignalingDevToneFreqOffDuration). This object should only be changed
by the configuration file.

2.2.11 DQoS Lite Enable

emtaEnableDQoSLite

(1.3.6.1.4.1.4413.2.2.2.1.6.1.7.0 Integer32)

This object specifies whether DQoS Lite is enabled. When enabled,
gateid enforcement is disabled, which makes the EMTA use service
flows (lite DQoS) even in absence of gate IDs. When DQoS lite
is disabled, gate ID enforcement on the EMTA is enabled, which
makes the EMTA use real DQoS (no lite DQoS).

2.2.12 RFC2833 Enable

emtaSignalingDtmfToneRelayRFC2833Support

(1.3.6.1.4.1.4413.2.2.2.1.6.4.8.0 Integer32)

This object contains the value which controls the usage of the
RFC2833 DTMF Relay. Setting this object to 'enabled(1)' causes
the MTA to use the DTMF Tone Relay as per RFC2833. Setting this
object to 'disabled(2)' causes the eMTA not to use RFC2833 for
DTMF Tone Relay. Setting this object to 'subtract(3)' causes eMTA
to subtract DTMF tones from the encoded audio but not generate
RFC2833 packets.

‧

enabled(1),

‧

disabled(2),

‧

subtract(3)

2.2.13 Configure MTA syslog server Ip address.

pktcEvent.mib

MIB

Default Value Access

pktcDevEvSyslogAddress

Prov. Server IP read-write

pktcDevEvSyslogAddress

(1.3.6.1.4.1.4491.2.2.3.1.3.0 InetAddress)

This MIB Object contains the IP address of the Syslog server. If this
is set to either 0.0.0.0 or 255.255.255.255 the device MUST inhibit
syslogtransmission. The use of FQDNs is syntactically allowed, but
discouraged since a failure to resolve them in a timely manner may leave
the device without access to the Syslog daemon during critical network
events. The type of address this object represents is defined by the MIB
Object pktDevEvSyslogAddressType.

If an SNMP SET results in a type that does not match that indicated by
the MIB Object pktcDevEvSyslogAddressType, the PacketCable device MUST

«
...
46
47
48
49
50
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Бренд: Billion Страницы: 1

Бренд: Zte Страницы: 74

Бренд: Zte Страницы: 2

Бренд: Zte Страницы: 12

Бренд: Maxon Страницы: 100

Бренд: ActionTec Страницы: 4

External 56K Call Waiting

Бренд: ActionTec Страницы: 33

Бренд: ActionTec Страницы: 119

F2 16 V4 Series

Бренд: Four-Faith Страницы: 36

Бренд: Enfora Страницы: 41

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 29

Бренд: Aiwa Страницы: 11

Бренд: Fritz! Страницы: 2

Бренд: AmazonBasics Страницы: 17

ARRIS SURFboard SB8200

Бренд: CommScope Страницы: 32

Бренд: Zhone Страницы: 2

Бренд: M2M Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды