Ambit U10C034 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 90

background image

85

If

false(2),

IPSEC Signaling Security is disabled for both the IPSEC Key Management and IPSEC

protocol (for the specific CMS).

Signaling MIB

This MIB module supplies the basic management object for the PacketCable Signaling protocols. This
version of the MIB includes common signaling and Network Call Signaling (NCS) related signaling objects.

PktcCodecType

Textual Convention defines various types of CODECs that MAY be supported. The list of CODECs
MUST be consistent with the CODEC specification

PKT-SP-CODEC-I05-040113.

PktcRingCadence

Represents a ring cadence in bit string format. The ring cadence representation starts with the first 1
in the pattern (the leading 0s in the MSB are padding and are to be ignored). Each bit represents
100ms of tone;

1

is tone,

0

is no tone.

60 bits are used for cadence representation, the least significant 4 bits represent repeatable
characteristics.

0000

means repeatable, and

1000

means non repeatable.

As an example, the hex representation of a ring cadence of 0.5 seconds on; 4 seconds off; repeatable
would be:

0x1 F0000000000.

PktcSigType

The various types of signaling that may be supported.

ncs

—Network Call Signaling; a derivation of MGCP (Media Gateway Control Protocol) version

1.0.

dcs

—Distributed Call Signaling; a derivation of SIP (Session Initiation Protocol) RFC 3261.

pktcSigDevCodecTable

This table describes the MTA supported CODEC types.

pktcSigDevCodecIndex

The index value which uniquely identifies an entry in the

pktcSigDevCodecTable.

pktcSigDevCodecType

A CODEC type supported by this MTA.

pktcSigDevCodecMax

The maximum number of simultaneous sessions of the specific CODEC that the MTA can support.

pktcSigDefNcsReceiveUdpPort

Contains the MTA User Datagram Protocol (UDP) receive port that is being used for NCS call
signaling. This object should only be changed by the configuration file, default value is

2427.

pktcSigNcsServiceFlowState

Contains a status value of the Call Signaling Service Flow.

not-active

indicates that the NCS SF is not being used, and has not tried to be created.

active

indicates that the NCS SF is in use.

error

indicates that the NCS SF creation resulted in an error and the best effort channel is used for

NCS Signaling

pktcNcsEndPntConfigCallAgentId

Contains a string indicating the call agent name (for example,

[email protected]).

The call agent

name after the character

@

MUST be a fully qualified domain name and MUST have a corre-

sponding

pktcMtaDevCmsFqdn

entry in the

pktcMtaDevCmsTable.

Troubleshooting

«
...
83
84
85
86
87
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Zlinx Xtreme ZXT9-RM

Бренд: B&B Electronics Страницы: 163

Бренд: u-blox Страницы: 79

I-STORM USB A01-AU1

Бренд: Atlantis Land Страницы: 2

Бренд: TC Communications Страницы: 23

Бренд: Ubee Страницы: 22

Бренд: Huawei Страницы: 59

Бренд: Huawei Страницы: 10

Бренд: Huawei Страницы: 16

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 20

Бренд: Huawei Страницы: 5

Бренд: Huawei Страницы: 21

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 32

Бренд: Huawei Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды