Ambit U10C034 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 90

background image

U10C034 Telephony Version v1.4 June 2008

72

5.1 Battery operation in different termperature

When temperature is over 45 degrees(C) or under 0 degrees(C), the battery charge will be disabled,
battChargerState will be 2 (sleep), and the modem is still in normal operation mode. When
temperature is over 55 degrees(C), the battery charge remains disabled, battChargerState will be 2
(sleep), and the modem will go into power save mode. After temperature is over 60 degrees(C) or
under -10 degrees(C),the battery charge & discharge both will be disabled. If then it goes down
below 57 degrees(C), the battery discharge will be re-enabled (

hysteresis

mechanism), and the

modem remains in power save mode. If it goes down below 42 degrees(C), the battery charge will be
re-enabled. If battery is fully charged, the battChargerStat value stays in 2 (sleep). For more
detailed description please refer section 5.2 and 5.3.

5.2 Adaptor Mode

The figure show you how battery/LED works in different room temperature if AC adaptor is
existing.

«
...
70
71
72
73
74
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Бренд: D-Link Страницы: 123

Бренд: D-Link Страницы: 6

Бренд: XtendLan Страницы: 54

Бренд: Huawei Страницы: 24

Бренд: Zoom Страницы: 67

Бренд: Dynex Страницы: 16

Бренд: Four-Faith Страницы: 35

Бренд: 3Com Страницы: 2

Бренд: RadioLinx Страницы: 16

Бренд: goTenna Страницы: 92

Бренд: CTC Union Страницы: 43

Бренд: Skyway Страницы: 23

Бренд: Flightcell Страницы: 12

Бренд: Terayon Страницы: 26

Бренд: AIS Страницы: 14

Бренд: Zte Страницы: 24

Бренд: ptcl Страницы: 133

Бренд: Kantronics Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды