Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 1 / 58

507961-01

Page 1 of 58

Issue 2128

INSTALLATION INSTRUCTIONS

96G2UHV

Warm Air Gas Furnace

Upflow/Horizontal Left Air Discharge

Direct Vent & Non-Direct Vent

Save these instructions for future reference

(P) 507961-01

*P507961-01*

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in manuals, be alert to

the potential for personal injury or death.

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, personal

injury or loss of life. Installation and service must be

performed by a licensed professional installer (or

equivalent), service agency or the gas supplier.

WARNING

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

CAUTION

Table of Contents

Unit Dimensions ..........................................................

Parts Arrangement.......................................................

Gas Furnace

................................................................

Shipping and Packing List ...........................................

Safety Information .......................................................

General ........................................................................

Installation .................................................................

Filters .........................................................................

Duct System ..............................................................

Venting Practices .......................................................

Condensate Piping ....................................................

Gas Piping

.................................................................

Electrical ....................................................................

Blower Performance ..................................................

Unit Start-Up ..............................................................

Other Unit Adjustments..............................................

Service.......................................................................

Repair Parts List ........................................................

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды