Allied 96G2UH045BV12 Скачать руководство пользователя | Manualshive

Страница: 52 / 58

background image

507961-01

Page 52 of 58

Issue 2128

Unit Start-Up

FOR YOUR SAFETY READ BEFORE OPERATING

Do not use this furnace if any part has been underwater.

A flood-damaged furnace is extremely dangerous.

Attempts to use the furnace can result in fire or explosion.

Immediately call a qualified service technician to inspect

the furnace and to replace all gas controls, control

system parts, and electrical parts that have been wet or

to replace the furnace, if deemed necessary.

WARNING

Danger of explosion. Can cause injury or

product or property damage. Should the

gas supply fail to shut off or if overheating

occurs, shut off the gas valve to the

furnace before shutting off the electrical

blower deck, before performing any

service procedure.

WARNING

Before attempting to perform any service or

maintenance, turn the electrical power to unit OFF at

disconnect switch.

CAUTION

BEFORE LIGHTING

the unit, smell all around the furnace

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

The gas valve on the unit is equipped with a gas control

switch (lever). Use only your hand to move switch. Never

use tools. If the switch will not move by hand, do not try to

repair it. Force or attempted repair may result in a fire or

explosion.

Placing the Furnace into Operation

This furnace is equipped with an automatic hot surface

ignition system. Do not attempt to manually light burners

on this furnace. Each time the thermostat calls for heat, the

burners will automatically light. The ignitor does not get hot

when there is no call for heat on these units.

Gas Valve Operation

1.

STOP!

Read the safety information at the beginning

of this section.

Figure 74.

2.  Set the thermostat to the lowest setting.
3.  Turn OFF all electrical power to the unit.
4.  This furnace is equipped with an ignition device which

automatically lights the burners. Do not try to light the

burners by hand.

5.  Remove the upper access panel.
6.  Move gas valve switch to OFF. See Figure 74.
7.  Wait  five  minutes  to  clear  out  any  gas.  If  you  then

smell gas, STOP! Immediately call your gas supplier

from a neighbor’s phone. Follow the gas supplier’s

instructions. If you do not smell gas go to next step.

8.  Move gas valve switch to ON. See Figure 74.
9.  Replace the upper access panel.
10.  Turn on all electrical power to the unit.
11.  Set the thermostat to desired setting.

NOTE:

When unit is initially started, steps 1 through

11 may need to be repeated to purge air from gas line.

12. If the appliance will not operate, follow the instructions

“Turning Off Gas to Unit” and call your service

technician or gas supplier.

Capacity

Gas

Manifold Pressure in w.g.

Supply Line

Pressure in

w.g.

0 - 10000 ft.

0 - 4500 ft.

4501 - 5500 ft.

5501 - 6500ft.

6501 - 7500ft.

7501-10000ft.

Low

Fire

High

Fire

Low

Fire

High

Fire

Low

Fire

High

Fire

Low

Fire

High

Fire

Low

Fire

High

Fire

Min.

Max.

All

Natural

1.7

3.5

1.6

3.3

1.5

3.2

1.5

3.1

1.7

3.5

4.5

13.0

Lp/

Propane

4.5

10.0

4.2

9.4

4.0

9.1

3.9

8.9

4.5

10.0

11.0

13.0

Table 14.

Manifold and Supply Line Pressure 0 - 10,000 ft.

«
...
50
51
52
53
54
...
»

Содержание 96G2UH045BV12



























































Отзывы:

Нет отзывов

Похожие инструкции для 96G2UH045BV12

Бренд: Bard Страницы: 59

Бренд: Hans Grohe Страницы: 32

Бренд: Payne Страницы: 49

PG8JAA Series G

Бренд: Payne Страницы: 52

Бренд: Payne Страницы: 62

Бренд: Carrier Страницы: 8

Бренд: Carrier Страницы: 60

Бренд: Carrier Страницы: 8

Бренд: Carrier Страницы: 60

Бренд: Walter Wilson Страницы: 48

Бренд: Lennox Страницы: 38

Бренд: Lennox Страницы: 58

Бренд: Heat Controller Страницы: 16

Бренд: Heat Controller Страницы: 22

Бренд: Unitary products group Страницы: 32

Бренд: Unitary products group Страницы: 2

Бренд: Reversomatic Страницы: 16

Бренд: Rapido Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды