Alliance Laundry Systems IYG065J Скачать руководство пользователя

Страница: 6 / 106

Failure 3: Safety Switch Activated

.............................................................

Failure 4: The Linen is Not Correctly Distributed in the Stage when the Ma-

chine Starts Up the Spinning Sequence

....................................................

Failure 5: Out of Balance High Spin

...........................................................

Failure 6: Door Switch Failure

...................................................................

Failure 7: Door Lock Switch Failure

...........................................................

Failure 8: Door Close Check at Start Failure

................................................

Failure 9: Door Lock Switch Failure at Cycle End

........................................

Failure 10: Target Temperature not Reached

................................................

Failure 11: Fill Failure

...............................................................................

Failure 12: Overfill Failure

.........................................................................

Failure 13: Heating Failure

........................................................................

Failure 14: Heating Time Failure

................................................................

Failure 15: Too Hot

...................................................................................

Failure 16: Coin Blocking 1

.......................................................................

Failure 17: Coin Blocking 2

.......................................................................

Failure 18: Door Lock Pre-test Before Start

................................................

Failure 19: Door Lock Test After Start

........................................................

Failure 21: Overflow Failure

......................................................................

Failure 24: Defective Level Sensor

.............................................................

Failure 25: Defective Temperature Sensor

...................................................

Failure 26: Undefined Mitsubishi Frequency Inverter Error Code

..................

Failure 27: Communication Fault Inverter

...................................................

Failure 28: THT (Mitsubishi) Time Out

.......................................................

Failure 29: OV3 (Mitsubishi) Time Out

.......................................................

Failure 31: Initialization Fault Inverter

........................................................

Failure 32: Verification Fault Inverter

..........................................................

Failure 35: Wrong Software Version

............................................................

Failure 36: The Linen is Not Correctly Distributed in the Stage Before the Start

Up of the Spinning Sequence

..................................................................

Failure 37: Drain Failure at the Spray Sequence

...........................................

Failure 39: Empty Soap Supply Box

............................................................

Failure 41: Service Due Warning

................................................................

Failure 42: No Network Connection

............................................................

Failure 43: Wrong Voltage Range Selection

.................................................

Failure 44: Incorect Selection of Machine Type

...........................................

Failure 45: Drum Rotation Sensor is not Working

.........................................

Failure 77: Time for Heating Blocking is Out

...............................................

Failure 80: Time for Dispensing Liquid Detergents is Out

............................

Failure 85: RTC Low Battery

.....................................................................

Failure 95: Watch Dog

..............................................................................

Failure 300-353: Mitsubishi Inverter Alarm Message

....................................

Failure 500-526: Memory Errors

...............................................................

102

Failure 560: USB Not Found

....................................................................

102

Failure 561: File Not Found

......................................................................

102

Failure 562: Export Failed

........................................................................

102

Failure 563: Import Failed

........................................................................

102

Failure 570-571: Card Reader Error

...........................................................

102

Failure 600-628: Software Errors

..............................................................

103

Service Information

............................................................................

104

DO NOT COPY or TRANSMIT

Part No. D1631ENR7

Содержание IYG065J











































































































Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды

Alliance Laundry Systems IYG065J, Оригинальное руководство пользователя

Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды