Alliance Laundry Systems IYG065J Скачать руководство пользователя | Manualshive

Страница: 102 / 106

background image

Diagnosing Failure 307

3. Check if the fault is persis-
tent.

If the fault is persistent, con-
tact the manufacturer.

Table 91

Failure 309: OLT-Error (STALL PREVENTION)

Diagnosing Failure 309

The output frequency has dropped to minimum because of cur-
rent limitation.

1. Check if the power supply is
sufficient high and stable dur-
ing extraction with load.

Repair the power supply.

2. Check if the drum rotates
normally by hand. No abnor-
mal high friction.

Repair / clean what is necessa-
ry.

3. Check if the motor windings
are OK.

Replace the motor.

Table 92

Failure 313-315: OPT/PUE-Error (OPTION FAULT/

PARAMETER UNIT LEAVE OUT)

The OPT/PUE-ERROR can happen occasionally by a very short
general mains power supply interruption. Due to the power inter-
ruption, the inverter was not able to reset itself correctly. In such
case the contactor must not be replaced. The Inverter must be re-
set by a longer power interruption.

Diagnosing Failure 313-315

If the inverter doesn't receive requests from the wash computer
(no serial communication), after about 10-30 seconds the inver-
ter will go into OPT/PUE-alarm state.

1. Check at the end of the
wash cycle, if the power sup-
ply contactor of the frequency
inverter switches is switched
off on all phases.

Replace the contactor if the
problem is persistent.

Table 93

Failure 335: FIN-Error (COOLING FIN INVERTER

OVERHEAT)

Diagnosing Failure 335

If the heatsink temperature of the inverter crosses it's max al-
lowed operation temperature, the inverter will go into FIN-
alarm state.

1. Check if the cooling fan of
the inverter (if present) rotates
normally.

Replace the cooling fan on the
inverter (on the heatsink of the
inverter).

2. Check if the cooling fan in
the washer that takes fresh air
to the inverter’s environment
(if present) rotates normally.

Replace the cooling fan of the
washer.

3. Check if the heatsink or the
cooling fans are not clogged
with dust/dirt so that fresh air
can circulate freely.

Clean what is necessary.

4. Check if the ambient tem-
perature of the washer is with-
in the specified limits. Refer to
Installation/Operation/Mainte-
nance Manual.

Take care that the ambient
temperature is within the
specified limits.

Table 94

Failure 500-526: Memory Errors

If a memory error occurs then something is going wrong with the
EEPROM.

Try to reload the washing Programs. Check for source of electri-
cal "noise".

Failure 560: USB Not Found

The error message is displayed when an attempt to read from or
write on a USB flash disk fails.

Failure 561: File Not Found

The error message is displayed when the respective file is not
found during an attempt to read from a USB flash disk.

Failure 562: Export Failed

The error message is displayed when an attempt to write onto a
USB flash disk fails.

Failure 563: Import Failed

The error message is displayed when an attempt to read from a
USB flash disk fails.

Failure 570-571: Card Reader Error

Problem with card reader payment system.

Troubleshooting

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

102

Part No. D1631ENR7

«
...
100
101
102
103
104
...
»

Содержание IYG065J











































































































Отзывы:

Нет отзывов

Похожие инструкции для IYG065J

Бренд: Hansa Страницы: 2

Бренд: Hansa Страницы: 2

3VT913NA - annexe 1

Бренд: BALAY Страницы: 25

3VT913NA - annexe 1

Бренд: BALAY Страницы: 30

Бренд: BALAY Страницы: 2

Бренд: BALAY Страницы: 2

Бренд: BALAY Страницы: 2

3VB350ID - annexe 1

Бренд: BALAY Страницы: 29

CSOW 4963TWCE-80

Бренд: Candy Страницы: 32

Бренд: Russell Hobbs Страницы: 66

Бренд: ZANKER Страницы: 28

Бренд: Omega Страницы: 6

Бренд: GE Страницы: 28

Бренд: Euromaid Страницы: 32

Бренд: Celsius Страницы: 13

Бренд: Zanussi Electrolux Страницы: 20

14S44 D XAD929C

Бренд: VALBERG Страницы: 180

Бренд: Kleenmaid Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды