Alliance Laundry Systems IYG065J Скачать руководство пользователя

Страница: 17 / 106

Available Wash Sequences

Available Wash Sequences: Prewash, Wash, Cooldown, Rinse,
Final Rinse, Soak, Spray, No Wash.

Available drain/extraction sequences: Drain, Extract, No drain,
Static drain, Rev drain.

The Creation of a Wash Program

•

A Wash Program is created step by step.

•

Each step always consists of a Wash sequence and a
Drain/Extraction sequence.

Programming the Wash Sequence

First choose the type of Wash sequence.

• PREWASH
• WASH
• COOLDOWN
• RINSE
• FINAL RINSE
• SOAK
• SPRAY
• No WASH

Then program all the related functions of the sequence.

Available functions

• Temperature
• Water Level
• Water Inlet Valves
• The Wash Speed
• The Reversing Interval times
• Supplies
• Sequence Time (length of step)
• Drain valve 1 - 2
• Pause Signal

Each step is pre-loaded with default settings. When creating a
program, you can choose to utilize these suggested settings.

Programming the Drain Sequence

After programming the Wash sequence, next program the Drain/
Extraction sequence.

• DRAIN
• EXTRACTION
• No DRAIN
• STATIC DRAIN
• REVERSING DRAIN

Then program all the related functions of the Drain/Extraction se-
quence.

Available functions

• Sequence Time (length of step)
• Speed
• Drain valve 1 - 2

You can skip a sequence between two by programming No
WASH or No Drain.

Example : The No drain sequence should be programmed be-
tween a wash and a cooldown sequence.

NOTE: A more detailed explanation for the specific se-
quences can be found in Chapter

Step 4: Programming

the Wash Part

Step 5: Programming the Drain Step

The Tumble Sequence

• The wash cycle will always end with the Tumble sequence.
• The tumble sequence takes 30 Seconds, then the program is

finished and the door can be opened.

•

The Tumble sequence cannot be skipped.

Programming the Functions

Limits

• To ensure the correct functionality of the washing machine

you have to program values within certain limits.

• If you program a value that falls below the minimal or above

the maximal programmable limit then the new value will not
be accepted and the previous value stays valid.

Programming the Water Temperature

Limits

• Minimum value : 33.8°F [1°C]
• Maximum value : 113°F [45°C] for the PREWASH and

SOAK and 197.6°F [92°C] for the WASH sequence.

• For RINSE, FINAL RINSE and SPRAY no Temperature can

be programmed.

Programming the Water Inlets Valves

• Depending on the programmed temperature the water inlet

valves are suggested.

• While the tub is filling with water, the computer controls the

water temperature. By switching on and off the hot and cold
water inlet valves the correct water temperature is obtained.

• For machines with a Top Soap Dispenser you have to consider

that by programming the water inlet valves, at the same time,
you are also selecting the soap Box at which the soap must be
added.

• If you want to program a wash sequence with :

• Cold Water : only Cold Inlet Valves must be programmed
• Warm or Hot water : Cold and Hot Inlet Valves must be

programmed

Top Soap Dispenser Machines

The Cold Water Inlet Valves

Basic Description of Controls

DO NOT COPY or TRANSMIT

Part No. D1631ENR7

Содержание IYG065J











































































































Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды

Alliance Laundry Systems IYG065J, Оригинальное руководство пользователя

Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды