Alliance Laundry Systems IYG065J Скачать руководство пользователя

Страница: 100 / 106

Failure Message Overview

Error

Number

Failure

Failure Name

Explanation

328

Err MB1*

Brake sequence error 1

Sequence errors during use of the brake function.

329

Err MB2*

Brake sequence error 2

330

Err MB3*

Brake sequence error 3

331

Err MB4*

Brake sequence error 4

332

Err MB5*

Brake sequence error 5

333

Err MB6*

Brake sequence error 6

334

Err MB7*

Brake sequence error 7

335

Err FIN

Heatsink overheat

Refer to

Failure 335: FIN-Error (COOLING FIN INVERTER

OVERHEAT)

336

Err OSD*

Speed deviation excess

Too big speed deviation during vector control.

337

Err ECT*

Encoder signal loss

Problem with the encoder signal.

338

Err E.1*

Option alarm (connector1)

Occurs if there is a contact fault of the connector between the in-
verter and the communication option or if the communication op-
tion is fitted to connector 1 or 2 or if the switch of the plug-in
option is not on the default setting.

339

Err E.2*

Option alarm (connector2)

340

Err E.3*

Option alarm (connector3)

341

Err ILF*

Input phase failure

1 phase of the 3-ph input was lost for more than 1 second. Repair
the 3-phase power supply.

342

Err PTC

PTC thermistor operation

Overtemperature of motor PTC (switch AU/PTC must be on
PTC).

1. Check if motor cooling fan (if present) functions normally.

2. Check for contact faults in the wiring. Refer to electrical
scheme.

343

Err PE2

Parameter storage error

Problem with parameter storage (EEPROM failure). If the fault is
persistent, replace the inverter.

344

Err CDO*

Output Current detection

Current exceeded the output current detection level.

345

Err IOH

Inrush overheat

Resistor inrush current limit circuit overheated.

1. Do not switch on/off the inverter frequently.

2. Wait approximately 15 minutes and try again.

3. If the fault is persistent, replace the inverter.

346

Err SER*

Communication error

Communication problem on the RS485 terminals connector.

347

Err AIE*

Analog input error

Overcurrent or overvoltage on input terminal 2/4.

348

Err USB*

USB communication error

USB communication check time interval has elapsed.

349

Err OS*

Overspeed

Speed exceeded the limit during encoder feedback control.

Table 87

continues...

Troubleshooting

DO NOT COPY or TRANSMIT

100

Part No. D1631ENR7

Содержание IYG065J











































































































Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды

Alliance Laundry Systems IYG065J, Оригинальное руководство пользователя

Результаты поиска

Содержание IYG065J

Отзывы:

Похожие инструкции для IYG065J

Бренды по названию

Популярные бренды