Alliance Laundry Systems IYG065J Скачать руководство пользователя | Manualshive

Страница: 60 / 106

background image

CHM2464N_SVG

60°

35 Min.

Prog 2: Warm W ash

5

4

3

2

1

1.

Progression bar

2.

Time unit

3.

Remaining time wash program

4.

Wash program name

5.

Program number

Figure 24

Advancing a Wash Program

If the Advancing a wash program function is enabled (item
Allow Advance in the Initialization menu):

• Press the START button to skip a particular step.

If the Advancing a wash program function is disabled:

• Switch into the SERVICE INFORMATION to skip a wash

program step. Refer to

How to Get into the Setup Mode

.

Wash Time

• Once the program has been started, the remaining cycle time

is displayed.

• The clock symbol indicates whether the time of the running

cycle is being counted down or not. If the clock symbol is not
flashing, it means that the cycle time is not being counted
down.

• The time for which the symbol is not flashing is the extra

time.

• The total wash time = programmed time (1) + the extra time

(2+3+4+5).
1.   The programmed time of the processes.
2.   The extra time for taking water.
3.   The extra time for draining (if the water is not drained in

30 sec and the extended drain time is started)

4. The extra time for heating if "Wait for temperature" is se-

lected.

5. The extra free run time at the end of the spin sequence.

• The display of remaining cycle time can be disabled in Pay-

ment menu – item “Show Prog Time”.

Program End

• The time on the display counts down until 0.

• At the end of the cycle, the door lock is released, the display

shows the UNLOAD message and it is possible to open the
door (unload the laundry).

Open the door and unload the machine.

• The Message UNLOAD will be erased and the machine is

ready to start a new program.

• The program overview is shown.

Water Fill Process

• Depending on the water temperature the cold and hot inlet

valves will be opened.

• The water level is measured by an electronic water level sen-

sor.

• If the Temperature Balance function is enabled, the Wash

Computer will control the water temperature until the target
temperature is reached. For Hot wash programs, extra heating
will be required after the fill process to reach the programmed
hot water temperature.

• In the standard wash tables you will find a Normal Low and

Normal High water level.

• These are the standard water levels :

• The Normal Low water level is used for the Prewash,

Wash and Soak sequence.

• The Normal High water level is used for the Rinse and Fi-

nal Rinse sequence.

• The water level can only be programmed between two limits:

• The lower limit is above the heating elements and the tem-

perature sensor.

• The upper limit is in the middle of the wash drum.

Heating Process

When "No Wait for Temperature" (No Wait for Heat) is selected:
• The machine will heat until the time of the specific wash step

is over or if the programmed temperature was reached.

• Even if the programmed temperature is not reached, the pro-

gram will start the next sequence if the time of the sequence is
over.

When "Wait for Temperature" (Wait for Heat) is selected:
• The machine will heat until the programmed temperature is

reached. The programmed time of the wash sequence will on-
ly start counting down from the moment that the target tem-
perature was reached.

WARNING

When the machines do not have electrical or steam
heating no "Wait for temperature" should be select-
ed in the Initialization Menu.

C068

Operation Menu

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

60

Part No. D1631ENR7

«
...
58
59
60
61
62
...
»

Содержание IYG065J











































































































Отзывы:

Нет отзывов

Похожие инструкции для IYG065J

FP-90LST060GMTL-N

Бренд: Midea Страницы: 5

Бренд: Kärcher Страницы: 15

Бренд: Hotpoint Страницы: 2

Бренд: Pacific hydrostar Страницы: 23

Бренд: V-ZUG Страницы: 68

Бренд: Greencut Страницы: 52

Бренд: Omega Страницы: 31

Бренд: Galanz Страницы: 32

Бренд: DAEWOO ELECTRONICS Страницы: 37

Бренд: Kärcher Страницы: 20

Profile PDWT400R

Бренд: GE Страницы: 2

Бренд: Briggs & Stratton Страницы: 36

Бренд: Lavor Страницы: 108

Speed Queen awn432sp

Бренд: Goedeker's Страницы: 12

Бренд: Hotpoint Страницы: 14

Бренд: Speed Queen Страницы: 2

Бренд: Waspper Страницы: 13

Бренд: BENDIX Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды