Alliance Laundry Systems IYG065J Скачать руководство пользователя | Manualshive

Страница: 101 / 106

background image

Failure Message Overview

Error

Number

Failure

Failure Name

Explanation

350

Err OD*

Position error

Too much difference between the position command and the po-
sition feedback during position control.

351

Err EP*

Encoder phase error

Rotation command different than the motor rotation direction.

352

Err E.11*

Opposite rotation deceleration

Rotation direction of the speed command different than the esti-
mated speed causing overload.

353

Err E.13

Internal circuit error

Problem with an internal circuit, replace the inverter.

* This option or function is not used. If you have this error anyway do the following :

1. Reload the inverter parameters.
2. If the fault is persistent, replace the inverter.

Table 87

Failure 300-301-302: OC Errors (OVERCURRENT)

Diagnosing Failure 300-301-302

1. Verify that there is no short
circuit on the output of the in-
verter. (loose wire of motor ca-
ble, motor windings, screws or
other loose parts inside the
motor terminal box,…)

Repair the short circuit.

2. Disconnect the motor cable
from the inverter and try again.

If you still have the error with
motor cable disconnected, re-
place the inverter.

Table 88

Failure 303-304-305: OV Errors (OVERVOLTAGE)

Diagnosing Failure 303-304-305

If the DC-voltage on the capacitors is too high, the inverter will
generate OV error.

1. Check if there was a high
unbalance during extraction,
which can be caused by put-
ting only half loads in the ma-
chine.

Put always a full load in the
machine drum.

2. Check if the supply voltage
is not too high.

Reduce the supply voltage.

3. Check if the fault is persis-
tent

If the fault is persistent, con-
tact the manufacturer

Table 89

Failure 306: THT-Error (INVERTER OVERLOAD)

Diagnosing Failure 306

If the output current of the inverter is abnormal high for some
time, the inverter will go into THT-alarm state.

1. Verify that the power supply
is sufficient and stable during
extraction with load.

Repair the power supply.

2. Make sure the drum rotates
normally by hand. No abnor-
mal high friction.

Repair / clean what is necessa-
ry.

3. Check if the motor windings
are OK.

Replace the motor.

Table 90

Failure 307: THM-Error (MOTOR OVERLOAD)

Diagnosing Failure 307

If the motor current is higher than allowed for a longer time, the
inverter will activate the electronic overcurrent protection to
prevent the motor from overheating and the inverter will go into
THM-alarm state.

1. Check if the drum rotates
normally by hand.

Repair / clean what is necessa-
ry.

2. Check if the motor windings
are OK.

Replace the motor.

Table 91

continues...

Troubleshooting

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

101

Part No. D1631ENR7

«
...
99
100
101
102
103
...
»

Содержание IYG065J











































































































Отзывы:

Нет отзывов

Похожие инструкции для IYG065J

Бренд: Daewoo Страницы: 17

Бренд: Daewoo Страницы: 16

INDEPENDENT 2800

Бренд: Lavor Страницы: 112

Бренд: GEAppliances Страницы: 72

Бренд: Hoonved Страницы: 18

Бренд: Manta Страницы: 19

Бренд: EdgeStar Страницы: 13

sunjoe SPX2598-ELT

Бренд: SNOWJOE Страницы: 20

Бренд: Daewoo Страницы: 50

Super 20 CL8761

Бренд: Speed Queen Страницы: 41

Бренд: Magic Chef Страницы: 12

Бренд: Kärcher Страницы: 22

Бренд: Daewoo Страницы: 15

Бренд: Sealey Страницы: 5

Бренд: Wascomat Страницы: 132

Бренд: Alliance Laundry Systems Страницы: 64

Бренд: Silverline Страницы: 76

Бренд: CORBERO Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды