Alliance Laundry Systems HWFB61QN1102, Руководство по обслуживанию

Страница: 115 / 138

801683
113
Section 5 Service Procedures
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
• Motor not grounded! Disconnect electric power before servicing motor.
W485
WARNING
(2) Open loading door. Carefully remove wire
clamp ring from groove with small flat
blade screwdriver. Spring is in 6 o’clock
position. Refer to
Figure 27 .
NOTE: To avoid damage to spring, use screwdriver
on wire clamp ring to the right or left of spring.
(3) Grasp loading door seal lip. Refer to
Figure 46 , Step 1.
NOTE: To avoid damage to door seal, DO NOT use
pliers or sharp objects to grasp the door seal lip. If
lip is damaged, seal will leak.
(4) Using a circular motion, pull seal up
( Figure 46 , Step 1), out ( Figure 46 , Step 2)
and down ( Figure 46 , Step 3).
(5) When seal releases from lip of front panel,
pull out and remove the seal from front
panel around door opening. Refer to
Figure 46 , Step 4.
(6) While supporting the front panel assembly,
remove the two bottom front corner screws.
Refer to
Figure 29 . Remove front panel
(with loading door attached) away from
washer as far as wires permit.
(7) Unplug wire harness from both the door
latch switch and from the door switch.
Refer to
Figure 48 . Remove clips holding
wire harness and door seal hose along top
flange of front panel and remove front
panel.
(8) Unlock and remove meter case service
door. Refer to Figure 30 .
(9) Remove shoulder screw from inside meter
case. Refer to Figure 30 .
(10) Remove two screws holding cabinet top to
front flange of side panel. Refer to
Figure 28 .
(11) Remove security bolt (if present) from left
rear corner of cabinet top. Refer to
Figure 30 .
c. If area or space permits, lift cabinet top to a
vertical position by hinging it on the rear
hinges. Refer to
Figure 23 .
NOTE: To avoid damage to hinges, be sure to
support cabinet top with a small chain or something
similar. Refer to Figure 23.
d. Run belt off inner basket pulley while slowly
turning pulley. Refer to Figure 45 .
e. Remove belt from motor shaft.
f. Cut the wire tie holding small harness
connector to motor, then disconnect both motor
harness connectors from motor.
g. Using a magic marker, outline the washer on
the front and rear adjusting bolt holding motor
to bracket so the belt can be tightened to the
same location.
h. Use a six inch piece of 2x4 to support motor.
Grasp the metal rod with a locking pliers and
remove four bolts and washers holding motor to
motor bracket. Refer to
Figure 45 and remove
motor out through front of washer.
Motor Installation –
a. Place new motor into washer and allow motor
to rest on washer base.
b. Reconnect harness connector to new motor.
Refer to Figure 45 .
c. Install new wire tie holding small harness
connector to motor frame. This is necessary to
prevent future service calls.
d. Lift motor into position within the motor
bracket and install the front pivot bolt and
washer. Refer to
Figure 45 . Then install the
rear pivot bolt and washer. Leave bolt snug, do
not tighten.
e. Pivot motor up into motor bracket and install
the front adjusting bolt and washer. Refer to
Figure 45 . Then install rear adjusting bolt and
washer. Leave bolts snug.
NOTE: Locate the magic marker spot made earlier
on the motor bracket. Pivot motor so front
adjusting bolt and washer are in this spot and
tighten both front and rear adjusting bolts. Then
tighten both pivot bolts.
f. Place belt on motor pulley, then carefully run
belt on inner basket pulley while slowly turning
pulley. Refer to
Figure 45 .