
3
3
- 28
Control of 3-WAY FLOW LOGIC
3. Wired Remote Controller / NRCG-FL
Description
A:
When the unit is in heating standby status, the
indicator appears.
While this indicator is displayed, the indoor fan turns off or on at low fan
speed.
B:
The currently selected operation mode is displayed.
*
The ST-NDHP 76/ST-NDHP 96 shows the dry indicator, but it does not
have a dry function.
C:
This is displayed if a different operation mode was selected already by
another remote control unit and indicates that the mode cannot be
changed.
D:
After turning on the mains power switch for the first time,
indicator
blinks on the display of the remote control unit. While this is displayed, the
system is automatically checking units, and so wait until the
indicator turns off to operate the remote control unit. When the TIMER
SET button is pressed to set the timer, the
indicator flashes.
E:
The currently selected FAN SPEED, fan angle and SWEEP status are
displayed.
F:
This is displayed only if an abnormality occurs within a unit.
G:
When the CHECK button is pressed for more than 4 seconds, the TEST
indicator appears. Then, press the ON/OFF operation button to start test
run.
H:
This is displayed to indicate that the system controller is being used for
control. Whe n
is flashing on the display, the operation is not accepted
by the system controller.
I:
This displays the unit number of the indoor unit selected with the unit
selection button or the indoor/outdoor unit where an error is indicated.
J:
This is displayed if it is time to clean the filter.
K:
When setting the timer, the selected timer mode is displayed. This displays
the time of the timer. (An alarm message is displayed when an error
occurs.) Pressing the TIMER SET button cycles through the options in this
order:
No Display
L:
This is displayed when using the remote control unit sensor.
M:
This is displayed if a function is unavailable when a button is pressed.
N:
This displays the temperature setting.
O:
This is displayed when a connected ventilation fan (available
commercially) is operating.
A
B
F
C
H
L
N
M
I
E
G
D
K
J
O
Unit No.
Indoor unit No.
Refrigerant circuit No.
1 – 2
■
Di
s
play
04-218 Airwell-3_1-38.qxp 01/06/2007 13:58 Page 28
Содержание EFL 100-3R410
