AIRTRONICS SD-6G, Руководство по эксплуатации

Страница: 4 / 92

Page 4
SaFETy anD USagE PREcaUTiOnS
gEnERaL SaFETy
l
Be certain to read this Operating Manual in its entirety.
l
'Safety First' for yourself, for others, and for your equipment.
l
Observe all the rules of the flying site or anywhere you
operate your radio control equipment.
l
If at any time during the operation of your model should
you feel or observe erratic operation or abnormality, end
your operation as quickly and safely as possible. DO NOT
operate your model again until you are certain the problem
has been corrected. TAKE NO CHANCES.
l
Your model can cause serious damage or injury, so please
use caution and courtesy at all times.
l
Do not expose the radio control system to water or excessive
moisture.
l
Please waterproof the receiver and servos by placing them
in a water-tight radio box when operating model boats.
l
If you have little to no experience operating models, we
strongly recommend you seek the assistance of experienced
modelers or your local hobby shop for guidance.
l
The low voltage alarm will sound when the transmitter
battery voltage drops to 6.7 volts. If this occurs, stop
using the transmitter as soon as possible, then replace or
recharge the transmitter batteries.
TRanSMiTTER PREcaUTiOnS
l
Turn the transmitter ON first, then turn the receiver ON. After using your model, turn the receiver OFF
first, then turn the transmitter OFF. It can be dangerous if you activate the components in reverse order
as the servos may start up inadvertently.
l
Before use, double-check that the transmitter and receiver batteries have sufficient power and/or are
sufficiently charged (if using Ni-Cd/Ni-MH batteries).
l
Never touch the transmitter antenna during use. Doing so may cause loss of transmitter output, making
it impossible to control your model.
l
The transmitter antenna should be rotated and angled so that the antenna is
as close to perpendicular to the ground as
possible during use. After use, to prevent
any chance of damaging the antenna, the
antenna should be rotated and moved into
the horizontal stowed position.
l
Do not expose the transmitter to excessive heat, moisture, fuel, exhaust residue, etc.
l
Do not expose the transmitter to excessive heat or direct sunlight. Leaving the transmitter in direct sunlight can damage the LCD.
l
Do not press the Bind Button during use. The signal is interrupted while the Bind Button is pressed. It may also require a short time
to restore the signal after releasing the Bind Button, which can be dangerous.
ON
OFF
Keep Antenna
Perpendicular
to Ground
Do Not Expose to Moisture
or Direct Sunlight
2.4ghz FREqUEncy BanD PREcaUTiOnS
l
The 2.4GHz frequency band may be used by other devices, and other devices in the immediate area may cause interference
on the same frequency band. Always before use, conduct a bench test to ensure that the servos operate properly. Also,
conduct a range check at the area of operation to ensure that the radio control system has complete control of the model at
the farthest reaches of the operational area.
l
The response speed of the receiver can be affected if used where multiple 2.4GHz transmitters are being used, therefore,
carefully check the area before use. Also, if response seems slow during use, discontinue use as quickly as possible.
l
If the 2.4GHz frequency band is saturated (too many transmitters on at once), as a safety precaution, the radio control system
may not bind. This ensures that your radio control system does not get hit by interference. Once the frequencies have been
cleared, or the saturation level has dropped, your radio control system should be able to bind without any problems.
l
Observe any applicable laws and regulations in place at your flying site when using the 2.4GHz radio control system.
l
Unlike frequency bands used with earlier radio control systems, reception with this 2.4GHz radio control system can be
adversely affected by large obstructions and concrete or steel structures between your model and the transmitter. Also, wire
mesh and similar barriers can adversely affect operation. Keep this mind to ensure the safety of your model.
This radio control system operates on the 2.4GHz frequency band. The 2.4GHz connection is determined by the transmitter
and receiver pair. Unlike ordinary crystal-based systems, your model can be used without frequency control.