background image

 

 

TBS UNIFY EVO 5G8 (HV)  

Video Transmitter 

 

 

OSD capable, license-free, high power long range and freestyle VTx 

Revision 2019-02-21 

 

The TBS UNIFY EVO is a new line of video transmitters which contains a professional On Screen Display 

(OSD), optimized for compatibility across multiple platforms and reduced to a small form factor, 

completely redesigned and tailored for use in small multirotors and FPV wings. It is tightly integrated with 

TBS Crossfire and TBS Crossfire-compatible products such as flight controls. 

Key features 

World’s smallest video transmitter containing a full-featured on-screen display 

25mW (up to 800mW with HAM license*) 

Built-in microphone (with disable feature!) 

One button frequency and power setup 

Device configuration through OSD 

SMA pigtail connector with frame mounting holes integrated 

High voltage 7-26V (2-6S LIPO) input 

Clean voltage output for FPV Camera (5V / 200mA) 

Superior input noise filtering  

2x CRSF Serial Port 

for OSD data, device setup, expansion port for sensors etc. 

Smartaudio V2.1 for one wire serial control  

High quality branded U.FL connector with additional screw locking 

USB connector for firmware update and setup through TBS Agent 

Firmware update support through CRSF when paired with TBS Crossfire System

 

 

 

 

1 

 

Summary of Contents for TBS UNIFY EVO















Reviews: