AIC WAIKATO Expresso 72560 Скачать руководство пользователя страница 37

Страница: 37 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Installation Test

The following steps are to be preformed by the dealer prior to the first milking. When using the

Control 72560 Detacher or stand

lone, the following will test the general operation of all valves,

cylinders, motors and controls.

Do not expose the Detacher Controls to high voltage, such as Cow Trainers! (High voltage
can damage the electronics).

Turn power supply and vacuum source on, Connect stall cock connector to the stall cock. This

will bring power and vacuum to the detacher.

2. Verify the pulsator is operating correctly by using a vacuum recorder.

The pulsator should be operating within the ISO (International Standards

Organization

’

s) guidelines.

3. Verify in the attached mode that the detacher extends the retractor rope and the shutoff valve

allows vacuum to the claw.

Verify in the detached mode that the detacher retracts the rope and the shutoff valve is closed

and there is no vacuum to the claw.

5. Verify that all control box screws and power cords connectors are tight to prevent moisture

leaks.

6. Consult with the dairy owner to be sure that the units are set up to give the desired take off or

end of milking signal performance.

7. Be sure that all 72560 controls are set

up the same.

8. If, using a stand

lone unit be sure under retractor type the unit is set

up as none. This will

allow the pulsator to continue to operate after the end of milking setting has lapsed.

CAUTION

Startup Procedures

Содержание Expresso 72560








































































Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды

AIC WAIKATO Expresso 72560, Руководство по установке

Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды