AIC WAIKATO Expresso 72560 Скачать руководство пользователя страница 27

Страница: 27 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Page 2

Retract Delay (soft take off)

The retract delay allows the vacuum in the claw to bleed off (diminish) before retracting the rope or

chain. This reduces the pulling force on the teats when removing the cups. Retract delay is

adjustable (see controls set up table)

Pull Time

The pull time is the amount of time the printed circuit board (PCB) sends a retract signal to

the detacher

’

s relay, which in turn sends power to the retractor motor.

Pull Time

After the Pull Time expires, power is again applied to the motor for the desired amount of time.

Sweep Delay and (On Time) Duration

The milk sweep removes any milk that might collect in the milk hose during the retract phase. The

Sweep Delay is the time between claw retract and when the vacuum sweep (vacuum to remove

milk) begins. The Sweep On Time is the duration vacuum is applied to the claw. Both the Sweep

delay and sweep

time are programmable, (see Control Set

up Table).

Pulsation Rate

This setting establishes the number of pulsation cycles per minute.

Pulsation Ratio (Front)

This setting determines the milk to rest ratio as a percentage on the front two quarters of your

milker unit.

Pulsation Ratio (Rear)

This setting determines the milk to rest ratio as a percentage on the rear two quarters of your

milker unit.

Setup Definitions

Содержание Expresso 72560








































































Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды

AIC WAIKATO Expresso 72560, Руководство по установке

Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды