AIC WAIKATO Expresso 72560 Скачать руководство пользователя страница 13

Страница: 13 / 71

Expresso Tie Stall

(AIC) 608.526.6882

The

72560™

has a hook on the top to hang the detacher during milking. For proper milking unit

positioning and retraction location, the detacher needs to be positioned beside the cow approxi-

mately six inches behind the cow

’

s front shoulder (See the following illustration). If the detacher is

hung from the pipeline or structure toward the head of the cow, the detacher rope may not be long

enough and/or the claw may hit the floor during retraction.

•

Typically, ¼

”

galvanized cable is used for handing the detacher units during milking time. The

cable can usually be anchored to a wall at each end of the facility.

•

The cable should be high enough to allow the user to view the control over the backs of the

cows.

•

The detacher should be positioned properly with respect to the udder in order to

provide good retract motion.

•

The cable will need additional supports over the length of type of support is

recommended between each stall cock. Putting the support between stall cocks will reduce

the interference of the supports during milking time.

Try to avoid crossing walkways with the cable if the cable will be low enough to Interfere with safe

passage. If this situation can

’

t be avoided hand a flag, or other signal to mark the cable location.

The steel cable and related hardware must be supplied locally. Be sure that the cable does not in-

terfere with cow trainers. To avoid damage to the detacher control electronics, Cow

Trainers MUST Be OFF during milking

Installing a Steel Cable to Hang the

72560™

for Milking

Milking Support Cable System

Steel Cable

48in (1219cm)

80in

85in

(2032cm—

21596

cm)

Содержание Expresso 72560








































































Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды

AIC WAIKATO Expresso 72560, Руководство по установке

Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды