AIC WAIKATO Expresso 72560 Скачать руководство пользователя страница 56

Страница: 56 / 71

Expresso Tie Stall

(AIC) 608.526.6882

Make sure power to the detacher is

TURNED OFF

Using a

9/64”

(4mm ) Allen wrench, loosen the four control box screws holding the

front switch cover assembly.

Pull the switch cover assembly off the enclosure case back and unplug the ribbon

connector to the PCB.

Remove the green wire connectors and the four mounting screws holding the PCB in

place.

Remove the PCB and replace it with the new one. Secure PCB and connect wires.

Snub tighten the control box cover, over tightening can stress the plastic box to the

point of cracking.

Power up the control and program settings.

Matching model number: The PCB is used in many models of AIC detachers,

therefore after installing enter set

up and at the end of the set

up table select the

appropriate model number for the detacher in use. The model number is shown on

the label on the side of the control.

After selecting the model you must reboot by selecting factory defaults

“

YES

”

Program Settings: For consistent milking, all the units in the barn should be set up the

same.

Replacing # 90020504 MLSO Solenoid

Make sure power to the detacher is

TURNED OFF.

To Access # 90020504 solenoid remove front cover and board.

Remove the vacuum tubes from the solenoid remembering the proper hook

up.

Electronic Control PC Board Removal and Replacement

Back view of 72560 Detacher

Pulsator Mounting

90020504

24 VDC Milk

Line Shut

off Valve

(inside case back)

Flow Cell Holder

Содержание Expresso 72560








































































Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды

AIC WAIKATO Expresso 72560, Руководство по установке

Результаты поиска

Содержание Expresso 72560

Отзывы:

Похожие инструкции для Expresso 72560

Бренды по названию

Популярные бренды