Agilent Technologies DSO80204B Скачать руководство пользователя страница 14

Страница: 14 / 161

Chapter 1: General Information

Accessories supplied

Accessories supplied

The following accessories are supplied.

• Mouse, Agilent part number 1150-7913

• Stylus, Agilent part number 1150-7997

• Keyboard, Agilent part number 1150-7809

• Accessory Pouch, Agilent part number 54810-68701

• Front-panel Cover, Agilent part number 54810-42201

• Calibration Cable Assembly, Agilent part number 54855-61620

• Precision 3.5 mm Adapters (qty 2), Agilent part number 54855-67604

• Probe De-skew and Performance Verification Kit, Agilent E2655B

• Power Cord (see chapter 6, “Replaceable Parts,” for available power cords)

• User's Quick Start Guide

Options and Accessories Available

For a complete list of available options and accessories see Agilent Technologies publication
number 5989-4604ENUS:

Infiniium 80000B Series Oscilloscopes Data Sheet

Specifications & characteristics

For complete specifications and characteristics, direct your web browser to www.agilent.com
and perform a search for the oscilloscope’s model number. Then select “Data Sheets” from the
Library.

Specifications that are pertinent to each test are given in the "Testing Performance" chapter.

Specifications are valid after a 30 minute warm-up period, and within

C from the temperature

at which the last self-calibration was performed.

Содержание DSO80204B

































































































































































Результаты поиска

Содержание DSO80204B

Отзывы:

Похожие инструкции для DSO80204B

Бренды по названию

Популярные бренды

Agilent Technologies DSO80204B, Руководство по обслуживанию

Результаты поиска

Содержание DSO80204B

Отзывы:

Похожие инструкции для DSO80204B

Бренды по названию

Популярные бренды