Agilent Technologies DSO80204B Скачать руководство пользователя страница 127

Страница: 127 / 161

Chapter 6: Replacing Assemblies

To remove and replace the hard disk drive

126

To remove and replace the hard disk drive

Use this procedure to remove and replace the hard disk drive. When necessary, refer to other
removal procedures. The graphics in this chapter are representative of the oscilloscope at the
time of this printing. Your unit may look different.

Disconnect the power cable and remove the top sleeve.

Remove the CD-ROM and hard drive cables from the cable clamps.

Figure 6-24

Removing cables from cable clamps

Remove the two Torx T20 screws holding the shock mount in place (see See Figure 6-
25).

You may need to use a Torx key to loosen the screws.

When re-assembling, torque the screws to 18 in-lb.

Tilt the disk drive assembly forward and lift up to remove.

C A U T I O N

DO NOT LET THE DISK DRIVE FALL!
Support the drive while removing the screws so that the drive does not fall.

Remove the four Torx T10 screws holding the disk drive onto the shock mount.

Cable
clamps

Содержание DSO80204B

































































































































































Результаты поиска

Содержание DSO80204B

Отзывы:

Похожие инструкции для DSO80204B

Бренды по названию

Популярные бренды

Agilent Technologies DSO80204B, Руководство по обслуживанию

Результаты поиска

Содержание DSO80204B

Отзывы:

Похожие инструкции для DSO80204B

Бренды по названию

Популярные бренды