Agilent Technologies DSO80204B Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 161

background image

102

Replacing Assemblies

Use the procedures in this chapter when removing and replacing assemblies and parts
in the Agilent Technologies oscilloscopes.

In general, the procedures that follow are placed in the order to be used to remove a
particular assembly. The procedures listed first are for assemblies that must be removed
first.

The graphics in this chapter are representative of the oscilloscope at the time of this
printing. Your unit may look different.

ESD Precautions

When using any of the procedures in this chapter you must use proper ESD precautions.
As a minimum you must place the oscilloscope on a properly grounded ESD mat and
wear a properly grounded ESD wrist strap.

C A U T I O N

AVOID DAMAGE TO THE OSCILLOSCOPE!
Failure to implement proper antistatic measures may result in damage to the oscilloscope.

Tools Required

The following tools are required for these procedures.

• Torx drivers: T6, T8, T10, T15, T20

• Socket wrench: 5/8 inch and 9/16 inch

• Medium size (3/16-in) flat-blade screwdriver

• Nut Drivers: 3/16-in, 9/32-in, 5/16-in, 5/8-in

• Torque driver, 0.34 Nm (3 in-lbs), 5 mm or 3/16-in hex drive

• Torque driver, 0.34 Nm (3 in-lbs), Torx T6 drive

C A U T I O N

REMOVE POWER BEFORE REMOVING OR REPLACING ASSEMBLIES!
Do not remove or replace any circuit board assemblies in this oscilloscope while power is applied.
The assemblies contain components which may be damaged if the assembly is removed or
replaced while power is connected to the oscilloscope.

W A R N I N G

SHOCK HAZARD!
To avoid electrical shock, adhere closely to the following procedures. Also, after disconnecting
the power cable, wait at least three minutes for the capacitors on the power supply to discharge
before servicing this oscilloscope. Hazardous voltages exist on the inverter for the display
monitor.

W A R N I N G

SHOCK HAZARD!
Read the Safety information at the back of this guide before performing the following procedures.
Failure to observe safety precautions may result in electrical shock.

«
...
101
102
103
104
105
...
»

Содержание DSO80204B


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSO80204B

Бренд: idiag Страницы: 12

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Magma Страницы: 16

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Mac Medical Страницы: 23

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

Бренд: PI Страницы: 65

Бренд: Calibre Fitness Страницы: 11

Novation Launchkey Mini

Бренд: Focusrite Audio Engineering Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды