Advantech EKI-7659C Скачать руководство пользователя страница 143

Страница: 143 / 147

131

Figure C.62: 802.1x/RADIUS

Port Auth

You can configure 802.1x authentication state for each port. The State provides Disable,
Accept, Reject and Authorize.

•

Reject:

the specified port is required to be held in the unauthorized state.

•

Accept:

the specified port is required to be held in the Authorized state.

•

Authorized:

the specified port is set to the Authorized or Unauthorized state in

accordance with the outcome of an authentication exchange between the Supplicant
and the authentication server.

•

Disable:

The specified port is required to be held in the Authorized state.

•

Click ‘Apply’.

Figure C.63: Port Auth

C.4.2 MAC Address Table

Use the MAC address table to ensure the port security.

Содержание EKI-7659C




















































































































































Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды

Advantech EKI-7659C, Руководство пользователя

Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды