Advantech EKI-7659C Скачать руководство пользователя страница 75

Страница: 75 / 147

63 Chapter3

Figure 3.32: 802.1Q VLAN Configuration

802.1Q Configuration

•

Pull down the select item menu of VLAN Operation Mode, and select Port Based mode.

•

Enable GVRP Protocol:

mark the check box to enable GVRP protocol that allows network devices to

dynamically exchange VLAN configuration information with other devices. If GVRP protocol is not
enabled, user has to set the tagging information manually.

•

Select the port that you want to configure.

•

Link Type:

there are 3 types of link type.

Access Link:

single switch only,

allow user to group ports by setting the same VID.

Trunk Link:

extended application of

Access Link

, allows user to group ports by setting the

same VID with 2 or more switches.

Hybrid Link: Both Access Link and Trunk Link are available.

•

Untagged VID:

assign the untagged frame VID.

•

Tagged VID:

assign the tagged frame VID.

•

Click

Apply

Group Configuration

Edit the existing VLAN Group.

•

Select the VLAN group in the table list.

•

Click

Apply

Содержание EKI-7659C




















































































































































Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды

Advantech EKI-7659C, Руководство пользователя

Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды