Advantech EKI-7659C Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 147

background image

EKI-7659C User Manual

62

Figure 3.31: Port based mode-Add interface

•

You will see the VLAN displays.

•

Use

Delete

button to delete unwanted VLAN.

•

Use

Edit

button to modify existing VLAN group.

Note

Remember to execute the “Save Configuration” action, otherwise the new
configuration will lose when switch power off.

802.1Q VLAN

Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN
across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into
the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.
You can create Tag-based VLAN, and enable or disable GVRP protocol. There are 256 VLAN groups to
provide configure. Enable 802.1Q VLAN, the all ports on the switch belong to default VLAN, VID is 1. The
default VLAN can’t be deleting.

GVRP allows automatic VLAN configuration between the switch and nodes. If the switch is connected to
a device with GVRP enabled, you can send a GVRP request using the VID of a VLAN defined on the
switch; the switch will automatically add that device to the existing VLAN.

«
...
72
73
74
75
76
...
»

Содержание EKI-7659C




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-7659C

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

Бренд: Dahua Страницы: 6

Бренд: QNAP Страницы: 39

Бренд: insys icom Страницы: 4

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Sinus 154 data II

Бренд: T-COM Страницы: 12

RoteFinder RF500S

Бренд: Multi-Tech Страницы: 134

Бренд: WTI Страницы: 178

TeraStation WSS WS5020N6

Бренд: Buffalo Страницы: 115

Бренд: C&H Technologies Страницы: 50

Бренд: Patton electronics Страницы: 8

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренд: N-Tron Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды