Advantech EKI-7659C Скачать руководство пользователя страница 40

Страница: 40 / 147

EKI-7659C User Manual

dhcpserver subnetmask

[Subnet mask]

Configure subnet mask for DHCP
clients

switch(config)#

dhcpserver subnetmask

255.255.255.0

dhcpserver gateway

[Gateway]

Configure gateway for DHCP clients

switch(config)#

dhcpserver gateway 192.168.1.254

dhcpserver dnsip

[DNS IP]

Configure DNS IP for DHCP clients

switch(config)#

dhcpserver dnsip 192.168.1.1

dhcpserver leasetime

[Hours]

Configure lease time (in hour)

switch(config)#

dhcpserver leasetime 1

dhcpserver ipbinding

[IP address]

Set static IP for DHCP clients by port

switch(config)#

interface fastEthernet 2

switch(config)#

dhcpserver ipbinding 192.168.1.1

show dhcpserver configuration

Show configuration of DHCP server

switch#

show dhcpserver configuration

show dhcpserver clients

Show client entries of DHCP server

switch#

show dhcpserver clients

show dhcpserver ip-binding

Show IP-Binding information of
DHCP server

switch#

show dhcpserver ip-binding

no dhcpserver

Disable DHCP server function

switch(config)#

no dhcpserver

security enable

Enable IP security function

switch(config)#

security enable

security http

Enable IP security of HTTP server

switch(config)#

security http

security telnet

Enable IP security of telnet server

switch(config)#

security telnet

security ip

[Index(1..10)] [IP Address]

Set the IP security list

switch(config)#

security ip 1 192.168.1.55

show security

Show the information of IP security

switch#

show security

no security

Disable IP security function

switch(config)#

no security

no security http

Disable IP security of HTTP server

switch(config)#

no security http

no security telnet

Disable IP security of telnet server

switch(config)#

no security telnet

3.1.4

Port Commands Set

Table 3.4: Port Commands Set

Netstar Commands

Level

Description

Example

interface fastEthernet

[Portid]

Choose the port for modification.

switch(config)#

interface fastEthernet 2

duplex

[full | half]

Use the duplex configuration
command to specify the duplex
mode of operation for Fast
Ethernet.

switch(config)#i

nterface fastEthernet 2

switch(config-if)

#duplex full

speed

[10|100|1000|auto]

Use the speed configuration
command to specify the speed
mode of operation for Fast
Ethernet., the speed can’t be set to
1000 if the port isn’t a giga port..

switch(config)#

interface fastEthernet 2

switch(config-if)

#speed 100

no flowcontrol

Disable flow control of interface

switch(config-if)#

no flowcontrol

security enable

Enable security of interface

switch(config)#

interface fastEthernet 2

switch(config-if)

#security enable

no security

Disable security of interface

switch(config)#

interface fastEthernet 2

switch(config-if)#

no security

Содержание EKI-7659C




















































































































































Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды

Advantech EKI-7659C, Руководство пользователя

Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды