Advantech EKI-7659C Скачать руководство пользователя страница 125

Страница: 125 / 147

113

Figure C.36: Port Trunk Status

C.2.5 Port Mirroring

The Port mirroring is a method for monitor traffic in switched networks. Traffic through
ports can be monitored by one specific port. That means traffic goes in or out
monitored (source) ports will be duplicated into mirror (destination) port.

•

Rx Destination Port:

There is only one port can be selected to be destination

(mirror) port for monitoring RX traffic which come from source port. User can connect
mirror port to LAN analyzer or Netxray.

•

Tx Destination Port:

There is only one port can be selected to be destination

(mirror) port for monitoring TX traffic which come from source port. User can connect
mirror port to LAN analyzer or Netxray.

•

Mark the check boxes to monitor source receiving or transmitting packets of each

port. And then, click ‘Clear’ button to clear the marks or click ‘Apply’ button to carry
the setting into effect.

Figure C.37: Port Mirroring

Содержание EKI-7659C




















































































































































Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды

Advantech EKI-7659C, Руководство пользователя

Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды