Advantech EKI-7659C Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 147

background image

EKI-7659C User Manual

60

3.2.3 Protocol

VLAN configuration

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow
you to isolate network traffic, so only the members of the VLAN will receive traffic from the same
members of VLAN. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a
group of network devices to another Layer 2 switch. However, all the network devices are still plugged
into the same switch physically.

The industrial switch supports port-based and 802.1Q (tagged-based) VLAN. The default configuration of
VLAN operation mode is “

Disable

”.

Figure 3.29: VLAN Configuration

VLAN configuration - Port-based VLAN

Packets can go among only members of the same VLAN group. Note all unselected ports are treated as
belonging to another single VLAN. If the port-based VLAN enabled, the VLAN-tagging is ignored.

In order for an end station to send packets to different VLAN groups, it itself has to be either capable of
tagging packets it sends with VLAN tags or attached to a VLAN-aware bridge that is capable of
classifying and tagging the packet with different VLAN ID based on not only default PVID but also other
information about the packet, such as the protocol.

«
...
70
71
72
73
74
...
»

Содержание EKI-7659C




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-7659C

Бренд: Makita Страницы: 2

Бренд: Netopia Страницы: 38

Бренд: TP-Link Страницы: 2

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

Бренд: ProCurve Страницы: 2

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Бренд: KYLAND Technology Страницы: 24

Бренд: Quatech Страницы: 98

Бренд: Idis Страницы: 16

HomePNA PCI Adapter

Бренд: City-Netek Страницы: 18

Бренд: Black Box Страницы: 12

Бренд: Aerotech Страницы: 62

Бренд: Idis Страницы: 40

Бренд: NetComm Wireless Страницы: 154

Бренд: StarTech.com Страницы: 16

Бренд: H3C Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды