Advantech EKI-7659C Скачать руководство пользователя страница 112

Страница: 112 / 147

EKI-7659C User Manual

100

•

Manual

: When the

Method

is selected as Manual, you can enter the IP configuration

into the related column fields directly to assign or change the IP configuration. Press
the ‘Set’ button to carry the setting into effect.

Figure C.15: IP Configuration—Manual

C.1.3 DHCP Server

The system provides the DHCP server function. Enable the DHCP server function, the
switch system will be a DHCP server.

•

DHCP Server:

Enable or Disable the DHCP Server function. Enable – the switch will

be the DHCP server on your local network.

•

Low IP Address:

the dynamic IP assign range. Low IP address is the beginning of

the dynamic IP assigns range. For example: dynamic IP assigning range is from
192.168.1.100 ~ 192.168.1.200. 192.168.1.100 will be the Low IP address.

•

High IP Address:

the dynamic IP assign range. High IP address is the end of the

dynamic IP assigns range. For example: dynamic IP assign range is from
192.168.1.100 ~ 192.168.1.200. 192.168.1.200 will be the High IP address.

•

Subnet Mask:

the dynamic IP assign range subnet mask.

•

Gateway:

the gateway in your network.

•

DNS:

Domain Name Server IP Address in your network.

•

Lease Time (sec):

It is the time period that system will reset the dynamic IP

assignment to ensure the dynamic IP will not been occupied for a long time or the
server doesn’t know that the dynamic IP is idle.

Содержание EKI-7659C




















































































































































Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды

Advantech EKI-7659C, Руководство пользователя

Результаты поиска

Содержание EKI-7659C

Отзывы:

Похожие инструкции для EKI-7659C

Бренды по названию

Популярные бренды