manualshive.com logo in svg

ADEMCO VISTA-10ES, Инструкция по установке и настройке

Приобретите ADEMCO VISTA-10ES сейчас и получите бесплатный Installation And Setup Manual для настройки системы безопасности. Скачайте руководство на manualshive.com и начните установку сразу же. Обеспечьте безопасность вашего дома с помощью надежной системы ADEMCO VISTA-10ES.

Поделиться
Скачать
background image

 

11-1 

 

S E C T I O N   1 1  

Testing the System 

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

 

Local Tests

 

After the security system installation is complete, test the system as follows: 

1. 

With the system in the disarmed state, check that all zones are intact. If a NOT READY message is displayed, press the [

✱

] key to 

display the faulted zone(s). Restore faulted zone(s) if necessary, so that the READY message is displayed.  

2. 

Enter the security code and press the TEST [5] key.  

The external sounder will sound for 1 second. If the backup battery is discharged or missing, the sounder may not turn on and a 
LOW BATTERY report will be transmitted with a TEST report.  

Note that the keypad will beep once every 40 seconds as a reminder that the system is in the Test mode.  

3. 

Fault and restore every sensor individually to assure that it is being monitored by the system. Each time a protection zone is 
faulted, the keypad will sound 3 beeps, and the identification of each faulted protection zone should appear on the keypad display. 

NOTE:  For 5800 wireless systems, triggering a zone set to Arm-AWAY, Arm-STAY, or Disarm will take the system out of the 

TEST mode and cause that action. 

4.  Walk in front of any interior motion detectors (if used) and listen for the required sound as movement is detected. The 

identification of the detector should appear on the display when it is activated. 

NOTE:  Wireless motion detectors (passive infrared units) will send signals out only if they have been inactive for 3 minutes.  

5. 

Follow the manufacturer's instructions to test all smoke detectors, to ensure that all are functioning properly. The identification of 
each detector should appear on the display when each is activated. 

6. 

Turn off the test mode by entering the security code and pressing the OFF [1] key. 

 

 

Communication Tests 

Alarm messages will be sent to the central station during the following tests. Notify CS personnel in advance that 
tests will be in progress. 

1. 

Arm the system (STAY) and fault one or more perimeter zones. After 15 seconds, silence alarm sounder(s) by entering the security 
code and pressing the OFF [1] key. 

Arm the system AWAY, and check the Entry/Exit zones for the programmed exit and entry delays. 

2. 

Check the keypad-initiated alarms that are in the system by using the Panic keys (or key pairs on some keypads). If a key (or key 
pair) has been programmed for audible emergency, the keypad will emit a steady alarm sound, and ALARM and zone number will 
be displayed. 

If a key (or key pair) has been programmed for silent emergency, there will be no audible alarms or displays, but a report will be 
sent to the central station. 

If a key (or key pair) has been programmed for fire, the keypad and external sounder will emit an interrupted alarm sound, and 
ALARM, FIRE and zone number will be displayed. 

Silence alarms by entering the security code and pressing the OFF [1] key. 

3. 

If Output Relay Units have been installed, test their programmed action. 

4. 

Notify the central station when all tests are finished, and verify results with them. 

To test the wireless part of the system and the RF Receiver, perform the two following tests: Transmitter Sniffer Mode and 
Go/NoGo Test Mode. 

 

 

Transmitter Sniffer Mode  

Make sure the system is disarmed before trying to enter this mode. 

1. Key 

Installer Code + [#] + [3].  This  initiates a procedure that checks that all 5800 Series transmitters have been properly 

programmed.  

NOTE:  If the communicator is in the process of sending a report to the central station, the system will not go into the Sniffer mode. If 

so, wait a few minutes, and try again. 

The keypad displays all zone numbers of wireless units programmed into the system. As the system receives a signal from each of the 
transmitters, the zone number of that transmitter disappears from the display. The transmitter codes may be checked upon 
installation, or in an installed system. 

All the wireless zone numbers should disappear after about 1-1/2 hours.  

NOTE:  Any transmitter that is not properly entered into the system will not turn off its zone number. 

2. 

Exit the Transmitter Sniffer mode by keying Installer code + OFF [1] key. 

 

 

 

Содержание VISTA-10ES

















































































Отзывы:

Нет отзывов

Похожие инструкции для VISTA-10ES

M86 Security 700 Evaluation Manual preview
700
Бренд: M86 Security Страницы: 86
ABB Welcome M21311P1-A Online Manual preview
Welcome M21311P1-A
Бренд: ABB Страницы: 15
Xilica Audio Design XA Series User Manual preview
XA Series
Бренд: Xilica Audio Design Страницы: 28
Wayne CWS Series Operating Instructions And Parts Manual preview
CWS Series
Бренд: Wayne Страницы: 16
Ultrasonic P100 Operation & Maintenance Manual preview
P100
Бренд: Ultrasonic Страницы: 16
3M LAD-SAF Instructions For Use Manual preview
LAD-SAF
Бренд: 3M Страницы: 88
3M Aqua-Pure AP510 Installation And Operating Instructions Manual preview
Aqua-Pure AP510
Бренд: 3M Страницы: 16
Teac LP-R550USB Quick-Start Recording Manual preview
LP-R550USB
Бренд: Teac Страницы: 2
Teac AG-D200 Quick Start Manual preview
AG-D200
Бренд: Teac Страницы: 4
U-Prox Multiplexer User Manual preview
Multiplexer
Бренд: U-Prox Страницы: 3
U-Prox WDC Quick Start Manual preview
WDC
Бренд: U-Prox Страницы: 2
Hanwha Vision TNV-C7013RC Quick Manual preview
TNV-C7013RC
Бренд: Hanwha Vision Страницы: 20
SGB DL 100 Manual preview
DL 100
Бренд: SGB Страницы: 49
Titan TOCS01 Manual preview
TOCS01
Бренд: Titan Страницы: 3
Abicor Binzel ABIPLAS CUT 200 W/MT Operating Instructions Manual preview
ABIPLAS CUT 200 W/MT
Бренд: Abicor Binzel Страницы: 100
liquidarc Handymig 170i Operator'S Manual preview
Handymig 170i
Бренд: liquidarc Страницы: 36
Miller Electric DS-75D16 Swingarc Owner'S Manual preview
DS-75D16 Swingarc
Бренд: Miller Electric Страницы: 48
Manta MM2040 TOUCHBOX User Manual preview
MM2040 TOUCHBOX
Бренд: Manta Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды