ADEMCO VISTA-10ES, Инструкция по установке и настройке

Страница: 16 / 80

VISTA-10SE Installation and Setup Guide
2-8
Installing the 5800TM Module
Installation of this module is necessary only if you are
using one or more 5827BD Wireless Bi-directional
keypads, or 5804BD Transmitters (wireless keys). Do
not cut any of the jumpers on the 5800TM when using
it with the VISTA-10SE.
For additional information, refer to the 5800TM’s
instructions.
Mounting the 5800TM Module
The 5800TM must be located near the RF receiver
(between one and two feet away from the receiver’s
antennas).
The 5800TM must not be installed within the control
cabinet. Mount the unit using its accompanying
mounting bracket.
Wiring the 5800TM Module
Connect the 5800TM to the control panel’s keypad
connection terminals, using the supplied connector with
flying leads, as follows:
Wire Terminal on Control
BLACK (Ground) Terminal 4
RED (+12VDC) Terminal 5
GREEN (Data to Control) Terminal 6
YELLOW (Data from Control) Terminal 7
BLUE Not Used
Installing Other 5800 Series Transmitters
1. To be sure reception of the transmitter's signal at
the proposed mounting location is adequate,
perform a Go/No Go Test, described in SECTION
11: Testing the System.
2. Install transmitters in accordance with the
instructions provided with each.
3. Set 5827, 5827BD, 5804BD transmitters to the
programmed House ID, using its DIP switches.
UL
5816 and 5817 transmitters do not have EOL
supervision of their loop wiring. Therefore, for UL
Household Burglary installations, the loop wiring
may not exceed 3 feet.
Transmitter Supervision
Except for some transmitters that may be carried off-
premises (5802, 5802CP, 5803, 5804, 5804BD, 5827,
and 5827BD), each transmitter is supervised by a
check-in signal that is sent to the receiver at 70-90
minute intervals. If at least one check-in is not received
from each supervised transmitter within a 12-hour
period, the “missing” transmitter number(s) and the
message CHECK is displayed.
NOTE: Refer to the listing of compatible devices in
SECTION 13: Specifications and Accessories.
I
n accordance with ULC standards, the
RF supervision period for the VISTA-
10SE is three hours for fire zones (Zone
Type 9) and 12 hours for all other zone
types.
UL
The following transmitters are not intended for
use in UL installations: 5802, 5802MN,
5802MN2, 5804, 5804BD, 5814, 5816TEMP,
5819, 5819WHS & BRS, 5827BD, and 5850.
The supervision for a particular transmitter in the
system that may also be carried off the premises (5801,
5802MN), may be turned off by enrolling it as a “UR”
(unsupervised RF) type, as described on next page.
5800 Series transmitters have built-in tamper
protection and annunciate as a CHECK condition if
covers are removed.
Transmitter Battery Life
•
Batteries in the wireless transmitters may last from 4
to 7 years, depending on the environment, usage, and
the specific wireless device being used. Factors such
as humidity, extreme temperatures, as well as large
temperature variations may all reduce the actual
battery life in a given installation. The wireless
system can identify a true low battery situation, thus
allowing the dealer or user of the system time to
arrange a change of battery and maintain protection
for that given point within the system.
•
Some transmitters (e.g., 5802 and 5802CP) contain
long-life but non-replaceable batteries, and no battery
installation is required. At the end of their life, the
complete unit must be replaced (and a new serial
number enrolled by the control).
•
Button-type transmitters (such as 5801, 5802, and
5802CP) should be periodically tested for battery life.
•
The 5802MN and 5804 Button Transmitters have
replaceable batteries.
Do not install batteries in wireless transmitters until
you are ready to enroll during system programming.
After enrolling, batteries need not be removed.