manualshive.com logo in svg

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 111 / 199

Поделиться
Скачать
ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 111

ABB i-bus® KNX 

PARAMETERS

7.4.93

Sending and switching delay after bus voltage recovery

This parameter is used to define the sending and switching delay after bus voltage recovery.

More information: → ⁠

Sending and switching delay, Page ⁠⁠185

.

Note

After bus voltage recovery, the device waits for the sending delay time to elapse before sending tele-
grams on the bus.

Option

2 ... 255 s

Prerequisites for visibility

• The parameter is in the parameter window 

Basic settings

.

7.4.94

Sending cycle

This parameter is used to define the cycle in which the group object 

In operation

 sends a telegram.

Option

00:00:01 … 00:10:00 … 18:12:15 hh:mm:ss

Prerequisites for visibility

• Parameter window 

Basic settings

 \ Parameter 

Enable group object "In operation"

 \ Option 

Yes

• The parameter is in the parameter window 

Basic settings

.

7.4.95

Setpoint for frost protection (building protection, heating)

This parameter is used to define the setpoint temperature that must not be fallen below in the 

Building

Protection heating operating mode.

More information: → ⁠

Explanation of the operating modes, Page ⁠⁠174

.

Note

The temperature value specified here must be lower than the value in the parameter 

Economy heating

setpoint

.

If the device is in the 

Heating operating mode, the setpoint is active in the following cases:

• Controller receives the status "Window open"
• The controller is deactivated via group object 

Request On/Off (master)

• Controller is placed in the 

Building Protection

 operating mode via group objects 

Operating mode nor-

mal (master)

 or 

Operating mode override (master)

Option

5 … 7 … 15 °C

Prerequisites for visibility

• Parameter window 

Channel X

 \ Parameter window 

Application parameters

 \ Parameter 

Channel

function

 \ Option 

Controller channel

• The parameter is in the parameter window 

Channel X

 \ parameter window 

Setpoint manager

.

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B  

111

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Отзывы:

Нет отзывов