ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 199

ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 104

ABB i-bus® KNX

PARAMETERS

7.4.85

Open if control value greater than or equal to

This parameter is used to define the control value as of which an On signal is sent to the valve drive. If
the control value is less than the value set here, an Off signal is sent.

Option

1 … 100 %

Prerequisites for visibility

• Parameter window

\ Parameter window

\ Parameter

\ Option

Open/close signal

• The parameter is in the parameter window

\ parameter window

7.4.86

Valve drive opening/closing time

This parameter is used to set the time the valve drive requires to open the valve completely (from posi-
tion 0 % to position 100 %) or close it completely.

Note

The time is listed in the technical data for the valve drive and corresponds to the total run time.

Option

10 … 180 … 900 s

Prerequisites for visibility

• Parameter window

\ Parameter window

\ Parameter

\ Options

Thermoelectric (PWM)

/

Open/close signal

• The parameter is in the parameter window

\ parameter window

7.4.87

Setpoint temperature offset when summer compensation ends

This parameter is used to define the setpoint temperature offset when summer compensation ends.

More information: → ⁠

Summer compensation, Page ⁠⁠187

.

Option

0.0 … 6.0… 12.7 °C

Prerequisites for visibility

• Parameter window

\ Parameter window

Application parameters

– Parameter

Channel function

\

Option

Controller channel

– Parameter

Basic-stage heating [controller]

all options except

Deactivated

• Parameter window

\ Parameter window

Setpoint manager

\ Parameter

Activate summer

\ Option

Yes

• The parameter is in the parameter window

\ parameter window

Setpoint manager

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

104

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

«
...
102
103
104
105
106
...
»

Содержание i-bus VC/S 4 1 Series








































































































































































































Отзывы:

Нет отзывов