ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 67

Страница: 67 / 199

ABB i-bus® KNX

PARAMETERS

7.4.19

Time for automatic reset to KNX operation

This parameter is used to define the time after which the device is automatically reset to the operating
state

KNX operation.

After the

Manual operation button is pressed, the device remains in the operating state Manual

operation until the button is pressed again or the set time expires.

Option

00:00:30 … 00:05:00 … 18:12:15 hh:mm:ss

Prerequisites for visibility

• Product variant:

– VC/S 4.2.1

• Parameter window

Manual operation

– Parameter

Manual operation

Option

Enabled

– Parameter

Automatic reset from manual operation to KNX operation

Option

Yes

• The parameter is in the parameter window

Manual operation

7.4.20

Automatic reset from manual operation to KNX operation

This parameter is used to define whether the device is reset from the operating state

Manual operation

to the operating state

KNX operation after an adjustable time.

Option

Automatic reset is deactivated. The operating state can be changed only using the

Manual operation

button.

Yes

The following dependent parameters are shown:
•

Time for automatic reset to KNX operation

Prerequisites for visibility

• Product variant:

– VC/S 4.2.1

• Parameter window

Manual operation

\ Parameter

Manual operation

\ Option

Enabled

• The parameter is in the parameter window

Manual operation

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы:

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 67 / 199

Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы: