ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 68

Страница: 68 / 199

ABB i-bus® KNX

PARAMETERS

7.4.21

Base setpoint is

This parameter is used to define which value corresponds to the base setpoint.

More information: → ⁠

Basic setpoint, Page ⁠⁠174

Note

If only the

Heating

operating mode or

Cooling

operating mode is configured, the base setpoint corre-

sponds to the respective

Comfort

setpoint.

Option

Comfort heating setpoint

The base setpoint corresponds to the setpoint for Comfort heating. If the base setpoint is changed
via the group object

Basic setpoint

, the setpoint for Comfort cooling shifts as well. The relative

distances between the two Comfort values remain unchanged.

Comfort cooling setpoint

The base setpoint corresponds to the setpoint for Comfort cooling. If the base setpoint is changed
via the group object

Basic setpoint

, the setpoint for Comfort heating shifts as well. The relative

distances between the two Comfort values remain unchanged.

Mean value between Comfort
heating and cooling

A mean value is calculated from the setpoints for Comfort heating and Comfort cooling. This mean
value is adopted as the base setpoint.

Prerequisites for visibility

• Parameter window

Channel X

\ Parameter window

Application parameters

– Parameter

Channel function

Option

Controller channel

– Parameter

Basic-stage heating [controller]

all options except

Deactivated

\ Parameter

\ Option

Relative

• The parameter is in the parameter window

Application parameters

– Parameter

Channel function

Option

Controller channel

– Parameter

Basic-stage cooling [controller]

all options except

Deactivated

\ Parameter

\ Option

Relative

• The parameter is in the parameter window

Channel X

\ parameter window

Setpoint manager

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы:

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 68 / 199

Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы: