ABB i-bus VC/S 4 1 Series Скачать руководство пользователя страница 94

Страница: 94 / 199

ABB i-bus® KNX

PARAMETERS

7.4.65

Enable group object "In operation"

This parameter enables the group object

In operation

Option

The group object is not enabled.

Yes

The following dependent parameters are shown:
•

Send value group object "In operation"

•

Sending cycle

The following dependent group objects are displayed:
•

In operation

Prerequisites for visibility

• The parameter is in the parameter window

Basic settings

7.4.66

KTY type

This parameter is used to set the KTY subtype.

Note

To ensure trouble-free function of the temperature input, the resistance values in the user-defined en-
try must increase according to the temperature values.
An incorrect entry results in incorrect output values.

Option

KTY X

The temperature sensor type KTY X is used. The resistance characteristic is predefined to suit the
temperature sensor type selected.

User-defined

The resistance values for the temperature sensor connected can be entered to suit the data sheet for
the temperature sensor.

The following dependent parameters are shown:
•

Resistance in ohms at x °C

Prerequisites for visibility

– Parameter

Option

Temperature sensor

– Parameter

Temperature sensor type

Option

KTY [-15…+110]

• The parameter is in the parameter window

Channel X

\ parameter window

Input x

7.4.67

Long operation after

This parameter is used to define the time from which actuation of a connected contact (e.g. button/
switch) is interpreted as long operation.

Option

1.0 … 10.0 s

Prerequisites for visibility

– Parameter

Option

Binary input

– Parameter

Distinction between long and short operation

Option

Yes

• The parameter is in the parameter window

Channel X

\ parameter window

Input x

Product manual | EN-US | VC/S 4.x.1 | 2CDC508220D0211 Rev. B

Note about navigation in the PDF: Key combination 'Alt + left arrow'
jumps to the previous view/page

Содержание i-bus VC/S 4 1 Series








































































































































































































Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы:

ABB i-bus VC/S 4 1 Series, Руководство по эксплуатации продукта, Страница: 94 / 199

Результаты поиска

Содержание i-bus VC/S 4 1 Series

Отзывы: