manualshive.com logo in svg

ABB ACS880-04F, Руководство по оборудованию, Страница: 21 / 172

Поделиться
Скачать
ABB ACS880-04F Скачать руководство пользователя страница 21

Introduction to the manual   21

Quick installation, commissioning and operating 
flowchart

Task

See

Plan the mechanical and electrical installation and acquire 
the accessories needed (cables, fuses, etc.).
Check the ambient conditions, ratings, required cooling air 
flow, input power connection, compatibility of the motor, 
motor connection, and other technical data.

Guidelines for planning the mechanical 
installation 

(page

 37

)

Guidelines for planning the electrical installation 

(page

 57

)

Technical data 

(page

 119

)

Resistor braking

 (page 

165

)

Option manual (if optional equipment is 
included)

Unpack and check the units. 
Check that all necessary optional modules and equipment 
are present and correct.
Only intact units can be started up.

Moving and unpacking the unit 

(page 

48

)

Installing the motor cable at the motor end 

(page 

77

)

If the drive module has been non-operational 
for more than one year, the converter DC link 
capacitors need to be reformed. (

Reforming the 

capacitors

, page 

114

)

Check the installation site. Fasten the base of the cabinet to 
the floor.

Examining the installation site 

(page

 47

)

Ambient conditions 

(page

 132

)

Guidelines for planning the mechanical 
installation

 (page

 37

)

Route the cables.

Routing the cables

 (page 

66

)

Check the insulation of the supply cable, the motor and the 
motor cable and the resistor cable (if present). 

Checking the insulation of the assembly

 (page

 

78

)

Installing the drive module
• Install the drive module into the cabinet.
• Install the additional components into the cabinet: for 

example, main disconnector, main contactor, main AC 
fuses, etc.

• Connect the motor cables to the drive module terminals.
• Connect the brake resistor and DC connection cables (if 

any) to the drive module terminals.

• If the main disconnector is installed into the cabinet, 

connect it to the drive module terminals and the input 
power cabling to the disconnector.

• Connect the cables from the drive module to the external 

control unit and install the control unit into the cabinet. 

Mechanical installation

 

(page 

47

)

Connecting the power cables 

(page 

80

)

Connecting the external control unit to the drive 
module 

(page 

86

)

Attaching the external control unit

 (page 

54

)

Overview of control cable connection process

 

(page 

83

)

Manuals for any optional equipment

Содержание ACS880-04F













































































































































































Отзывы:

Нет отзывов