manualshive.com logo in svg

ABB ACS880-04F, Руководство по оборудованию, Страница: 103 / 172

Поделиться
Скачать
ABB ACS880-04F Скачать руководство пользователя страница 103

Start-up   103

9

Start-up

Contents of this chapter

This chapter describes the start-up procedure of the drive.

Start-up procedure

1. Only qualified electricians are allowed to start-up the drive.

2. Make sure that the installation of the drive module has been checked according to the 

checklist in chapter 

Installation checklist,

 and that the motor and driven equipment are 

ready for start.

3. Perform the start-up tasks instructed by the cabinet-installer of the drive module.

4. Switch the power on, setup the drive control program, and perform the first start of the 

drive and motor. See the appropriate start-up guide or firmware manual. If you need 
more information on the use of the control panel, see 

ACS-AP-x Assistant control 

panels user's manual

 (3AUA0000085685 [English]).

•

For drives with resistor braking (D151), see also section 

Start-up

 on page 

168

.

•

For N7502, see also 

ACS880 drives with SynRM motors (N7502) 

supplement

 (3AUA0000145506 [English]).

•

For drives with ABB du/dt filter, check that bit 13 of parameter 

95.20 HW options 

word 1

 is switched on.

•

For drives with ABB sine filter, check that parameter 

95.15 Special HW settings 

is set to 

ABB sine filter

. For other sine filters, see 

Sine filter hardware manual 

(3AXD50000016814 [English]).

5. For drives with ABB motors in explosive atmospheres, see also 

ACS880 drives with 

ABB motors in explosive atmospheres

 (3AXD50000019585 [English]). 

Содержание ACS880-04F













































































































































































Отзывы:

Нет отзывов