ABB ACS880-04F Скачать руководство пользователя страница 47

Страница: 47 / 172

Mechanical installation 47

Mechanical installation

Contents of this chapter

This chapter describes how to install the drive module mechanically without the clear
plastic shrouds. The shrouds are attached after the power cabling.

Examining the installation site

Examine the installation site:

•

The installation site is sufficiently ventilated or cooled to transfer away the drive
losses.

•

The ambient conditions of the drive meet the specifications.

•

The material onto which the drive module is mounted must be non-flammable and
strong enough to carry the weight of the module.

•

There is enough free space above the drive to enable cooling air flow, service and
maintenance.

•

The floor that the drive is installed on is of non-flammable material, as smooth as
possible, and strong enough to support the weight of the drive.

See section

Ambient conditions

on page

132

for the allowed ambient conditions and

section

Losses, cooling data and noise

on page

127

for the required cooling air.

Содержание ACS880-04F













































































































































































Результаты поиска

Содержание ACS880-04F

Отзывы:

ABB ACS880-04F, Руководство по оборудованию, Страница: 47 / 172

Результаты поиска

Содержание ACS880-04F

Отзывы: