ABB ACS880-04F Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 172

ABB ACS880-04F Скачать руководство пользователя страница 37

Guidelines for planning the mechanical installation 37

4

Guidelines for planning the
mechanical installation

Contents of this chapter

This chapter guides in planning drive cabinets and installing the drive module into a user-
defined cabinet. The chapter gives cabinet layout examples and free space requirements
around the module for cooling. These guidelines are essential for the safe and trouble-free
use of the drive system.

Limitation of liability

You must always plan and make the installation according to applicable local laws and
regulations. ABB does not assume any liability whatsoever for any installation which
breaches the local laws and/or other regulations.

Installation alternatives

The drive module can be installed from the flange onto a cabinet wall or a mounting plate
with the heatsink (degree of protection of IP55) in a cooling air channel or outdoors. The
control circuit compartment side of the module (IP20 degree of protection) is to be placed
in clean air. The drive module can also be installed from the heatsink with mounting
brackets which are included in the delivery as standard.

The drive module can be cabled from top or bottom to cable connection terminals or
sideways with busbars directly to the module busbars at its side.

«
...
35
36
37
38
39
...
»

Содержание ACS880-04F













































































































































































Отзывы:

Нет отзывов