ABB ACS880-04F Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 172

ABB ACS880-04F Скачать руководство пользователя страница 86

86 Electrical installation

Connecting the external control unit to the drive module

WARNING!

Handle the fiber optic cables with care. When unplugging optic

cables, always grab the connector, not the cable itself. Do not touch the ends of
the fibers with bare hands as the fiber is extremely sensitive to dirt.



Routing the control unit cables into the drive module

Route the control unit connection cables to the drive module through the slot in the middle
front cover at the front or left side or from below or above. When routing through the
middle front cover, remove the plate which covers the slot. Then, install the rubber
grommet into the slot from the accessories box (no. 6 in the package drawing on page

).



Connections to the drive module

1. Connect power supply cable of the control unit to the BPOW connector and the ground

wire of the cable to the ground terminal.

2. Connect the BGDR cable to the BGDR connector.

3. Connect the fiber optic cables to the V:20 and V10 connectors.

Secure the cables at the clamps.

V10, V20

BPOW

BGDR

1

3

1

2

«
...
84
85
86
87
88
...
»

Содержание ACS880-04F













































































































































































Отзывы:

Нет отзывов