3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 90

3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 87

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

79

Figure 10-‐8

IP Address Filter

10.5

Viewing Device Information

Enter the Device Information interface:

!

Configuration

>

Basic Configuration

>

System

>

Device Information

!

Or

Configuration

>

Advanced Configuration

>

System

>

Device Information

!

In the

Device Information

interface, you can edit the Device Name.

Other information of the network speed dome, such as Model, Serial No., Firmware Version, Encoding
Version, Number of Channels, Number of HDDs, Number of Alarm Input and Number of Alarm Output
are displayed. The information cannot be changed in this menu. It is the reference for maintenance or
modification in future.

Figure 10-‐9

Device Information

10.6

Maintenance

REBOOTING THE SPEED DOME

Steps:

1)

Enter the Maintenance interface:

Configuration

>

Basic Configuration

>

System

>

Maintenance

«
...
85
86
87
88
89
...
»

Содержание VSX-PTZ-2MP-EXT20



























































































Отзывы:

Нет отзывов