3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 69

Страница: 69 / 90

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

Figure 6-‐50

Exception Settings

Click

to save the settings.

DETECTING AUDIO EXCEPTION

Purpose:

When you enable this function and audio exception occurs, the alarm actions will be triggered.

Steps:

Enter the video audio exception detection interface:

Configuration > Advanced Configuration > Events > Audio Exception Detection

Figure 6-‐51

Audio Exception Detection

Check

Enable

under

Audio Input Exception

checkbox to enable the audio input exception

detection.

Check

Enable

under

Sudden Change of Sound Intensity

checkbox to enable the sudden change

detection.

Sensitivity

: Range [1-‐100], the smaller the value the more severe the sound change will

trigger the detection.

Sound

Intensity

Threshold

: Range [1-‐100], it can filter the sound in the environment, the

louder the environment sound, the higher the value should be. You can adjust it according to
the actual environment.

Содержание VSX-PTZ-2MP-EXT20



























































































Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы:

3xLogic VSX-PTZ-2MP-EXT20, Руководство пользователя, Страница: 69 / 90

Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы: