3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 90

3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 12

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

4

DETECTING AND CHANGING THE IP ADDRESS

You need the camera IP address to connect to the network camera.

Steps:

1)

To get the IP   address, the 3xLOGIC VISIX setup utility, a software tool which can automatically   detect the
online network cameras in   the LAN and   list the device information   including IP address, subnet mask, port
number, device serial number, device version, etc., shown   in   Figure 2-‐3.

2)

Change the IP address and subnet mask to the same subnet as that of your computer.

3)

Enter the IP address of network camera in the address field of the web browser to view the live video.

Note:

!

The default IP address is 192.0.0.64 and the port number is 8000. The default user name is admin, and
password is 12345.

!

For accessing the network camera from different subnets, please set the gateway for the network camera
after you logged in. For detailed information, please refer to

Section 5.3.1

Configuring TCP/IP Settings

.

Figure 2-‐3

: 3xLOGIC VISIX detection utility

«
...
10
11
12
13
14
...
»

Содержание VSX-PTZ-2MP-EXT20



























































































Отзывы:

Нет отзывов