3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 35

Страница: 35 / 90

User Manual

| VISIX 5 Inch Speed Dome Camera

Speed Dome Configuration

6.1

Configuring Local Parameters

NOTE:

The local configuration refers to the parameters of the live view and other operations

using the web browser.

Steps:

Enter the Local Configuration interface:

Configuration > Local Configuration

Figure 6-‐1

Local Configuration Interface

Configure the following settings:

Live View Parameters:

Set the protocol type, stream type, image size and live view

performance.

Protocol Type:

TCP, UDP, MULTICAST and HTTP are selectable.

TCP:

Ensures complete delivery of streaming data and better video quality,

however the real-‐time transmission will be affected.

UDP:

Provides real-‐time audio and video streams.

HTTP:

Allows the same quality as of TCP without setting specific ports for streaming

under some network environments.

MULTICAST:

It’s recommended to select the protocol type to

when using the Multicast function.

For other information about Multicast, refer to

Section

6.3.1 Configuring TCP/IP Settings

Содержание VSX-PTZ-2MP-EXT20



























































































Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы:

3xLogic VSX-PTZ-2MP-EXT20, Руководство пользователя, Страница: 35 / 90

Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы: