3xLogic VSX-PTZ-2MP-EXT20 Скачать руководство пользователя страница 45

Страница: 45 / 90

User Manual

| VISIX PTZ Network Camera

10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

Figure 6-‐16

Protected LAN

Before connecting the Network Camera to the protected LAN, please apply a digital
certificate from a Certificate Authority.

The network camera requests access to the protected LAN via the authenticator (a switch).

The switch forwards the identity and password to the authentication server(RADIUS
server).

The switch forwards the certificate of authentication server to the network camera.

If all the information is validated, the switch allows the network access to the protected
network.

Steps:

Connect the network camera to your PC directly with a network cable.

Enter the 802.1X Settings interface:

Configuration >

Advanced Configuration >

Network > 802.1X

Figure 6-‐17

802.1X Settings

Check the

Enable IEEE 802.1X

checkbox to enable it.

Configure the 802.1X settings, including user name and password.

Network Switch

RADIUS

Server

Network Dome

Net

Authenticator

Authentication
Server

Содержание VSX-PTZ-2MP-EXT20



























































































Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы:

3xLogic VSX-PTZ-2MP-EXT20, Руководство пользователя, Страница: 45 / 90

Результаты поиска

Содержание VSX-PTZ-2MP-EXT20

Отзывы: